Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I am merging a PWM_driver example with a ble-peripheral-blinky example to generate PWM signals with user-defined arbitrary phase-shift and duty cycle.
I am done...
Hello,
I have nrf52832 platform and my version of softDrive is (nRF5_SDK_15.3.0_59ac345).
My problem is regarding GPIO configurations are NOT retained ,when the nRF52832...
Dear Support term:
The Restful of Nrf Cloud is not work.
The node should have more that 100 data, so get ListMessages should give us pageNextToken.
Yes the result give...
Hi all,
I am using a custom board with NRF 52840 with SDK15.2 as slave and STM as master. I cannot receive right data, but the data to STM is right.
The above are...
Hi,
I am using an nRF52833dk to run a simple async SPI transceive API using k_poll My code is as below, for some reason it always returns BUS FAULT error Code:
Error...
Hello,
I face at least 2 problems and need some support.
What I want to achieve is that the DTM runs at our customer hardware for radio and later on BLE certification...
Hello !
In PS1.7 chapter 6.4.5 Encrypting packets on-the-fly in radio transmit mode is explained encryption of a short packets (MODE.LENGTH = Default).
But when MODE...
Hi there, I'm performing an throughput analysis using an nRF52 development board (BMD-350) and a Raspberry Pi 4B (Ubuntu 20.04, BlueZ 5.54) with an BLE 5.0 adapter. For measuring...
Hi,
I want to use the bsp button to our project, so I tested on the example "ble_app_blinky",
I modified the app button to bsp button, add two custom events to the bsp_event_t...
Hi Devzone,
I've been trying to verify and validate the performance of Instaburst mesh packets against regular ones. I modified a build of the mesh light switch example...
Hello,
I have been trying to get the thingy:91 up for 3 weeks or more now from Sri Lanka. I have made a lot of progress in getting data connectivity via MQTT to thethings...
`Hi There,
For nRF52840 board, If I want to fully disable JTAG or SWD lines after flashing, then what are the options to achieve it.
Questions:
1) If I want to disable...
My use case: There are different but similar peripherals advertising with 1M uncoded or coded PHY. Some of them are even advertising in mixed mode.
Question: How to connect...
Hello all,
I hope you are well. I am currently developing a product on the nrf52810 platform. I have a custom board and now have the BLE functional on the board. The next...
Good Day.
I want to measure the approximate voltage level on the battery in the nrf52820 microcontroller using a comparator (COMP) operating in Single-ended mode. I use...
