This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
i have nrf52832 using nrf sdk version_17 and s132.
I have application for logging
i have followed steps:
1). intially device in sleep mode
current: 0.35 micro Amp...
Hi,
I am working at a project that was abandoned by a guy that worked on my position. I have to fix some issues and add some features. I'm using SDK 17.0.2, my IDE is VSCodium...
Dear all,
I am now using two nrf52840DK and nrf connect sdk v1.7.1,and I want to send packet using llpm mode between two devices,one is receiver and the other is sender...
I need a battery-powered programmable device to communicate via Bluetooth to a headset, and communicate with another device via serial (TXD/RXD) interface. Performance requirements...
Hello,
I am writing a single byte value to a cypress module using write with response (BLE_GATT_OP_WRITE_REQ). For some reason the peripheral will receive the value but...
Hi!
I am trying to develop a way for a Bluetooth Central and Bluetooth Peripheral using Secure Connections (security mode 1 level 2 if I'm not mistaken) using a static...
Dear nRF,
I have couple of nRF21540-dk boards (PCA10112) in my hand. I would like to use nRF Connect Direct Test Mode to activate TX and RX.
I found that the tool lacks...
Hi,
We are design custom Board using nRF52840 SOC.
We are operating it in Normal mode, using internal DCDC converter
We have used configuration 5 from reference design...
I am taking over a firmware Bluetooth project and am reading the code that is having some issues. Below is a snippet from a BLE characteristic read callback. Here a double...
I set a timer on the net core of nrf5340. The timer sets an interrupt of 10s. After the chip is reset and runs for 10s, the while (1) of the main function is interrupted,...
SDK Environment: nRF Connect SDK v1.7.1 Target: Decawave DWM1001-DEV. This uses the nRF52832
If I add CONFIG_LOG=y to "prj.conf" in the zephyr sample peripheral_dis, when...
Hello,
I'm working with a NRF52840 DK and a module BLE nrf805.
I'm programming thanks to the software SEGGER.
I have sent the blinky simple in my dev kit to test a...
Hello,
I am using the Segger Embeddd Studio from the nRF Connect Desktop and the nRF52840-DK board.
I am working over the project into the "ses" directory for SoftDevice...
