Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Dear Nordic，
We developed a product based on the nRF52833 chip, with an external antenna, 3dBi gain. Use a smartphone to scan the product in the outdoor，the transmission...
The product we are developing will be using a proprietary radio protocol. While in receive or send mode, the radio will either read the Tx data from a buffer via Easy DMA...
Hi,
I'm trying to download hex file to our custom development board which has an nRF5340 on it using the external JLINK on the nRF5340 dev kit. I'm using nrfjprog:
nrfjprog...
Greetings. I am trying to implement a custom cluster with attribute reporting, however, for some reason, i am unable to start reporting of such attributes. I have started...
Hi,
we are developing an application using the nrf42840, Softdevice S140 7.0.1 and nRF5 SDK v16.0.0. We develop the code both on central and peripheral side. So we have...
Hi,
I have two 52840DK,
OS : Windows10 X64
example: \ncs1.7.1\zephyr\samples\bluetooth\periodic_sync\
I didn't change the code, Whether I set [CONFIG_BT_LL_SW_SPLIT...
Hi,
nRF Conncet SDK1.7.1, Windows10 X64.
\ncs1.7.1\zephyr\samples\bluetooth\periodic_adv\,
building and debug work well,and i set the device name "PerAdv", then reload...
Hello
I'm trying to use the example code for ble_app_uart and it doesn't seem to work. I copied the folder for pca10028 and changed processor from nrf51422 to nrf51802 everywhere...
I am using four ADC inputs to the 9160.
I am driving each input from an op amp buffer as in the attached schematic.
ADC channels 0, 2, and 3 work as expected. As for channel...
I am trying to move our existing code based on the recommended NCS SDK. I was able to get MCU boot and SMP working, however, the update is extremely slow. I now seem to be...
I have developed a project using 9160. When I start up with the client board, the log will show that at command execution error occurs when I start up. Why is this? I admit...
Hello nRF community,
I am currently testing some Memfault application that comes with the nRF SDK v1.7.0. I have a custom board designed around the nRF9160 and have been...
Hey,
I'm developing and upgrading a BT mesh to Zephyr 2.7.99 and the base functions work, but my Node keep crashing and I don't know from where. It gives the following...
First off, I see a new changed requirement for making Public tickets:
To raise a public support ticket you need to provide your location in profile. profile Please fill...
Hi Everyone,
I'm having problems getting GPIOTE_IRQHandler_v() to run.
"NRF_GPIOTE->INTENSET = 1" causes my Nano 33 BLE to crash if "(GPIOTE_CONFIG_POLARITY_LoToHi <<...
