Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I noticed the minimal b0 immutable bootloader build does not fit anymore.
I used the example here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples...
Hello,
We are using NRF52832 to design a loss preventer product ,can you help to review the design SCH and PCB layout before PCBA making ? main including RF desing , GPIO...
Hi, I was trying to a project that includes edge impulse and nRf5340DK. I successfully run the example project t they provided and now try to use the library provided by edge...
Trying to do DFU over ZigBee, but nrfutil failes:
Gets this problem constantly. I have check all the examples and everything, doble checked all parameters, but always the...
Hello.
I am trying the SEGGER Embedded studio's open nRF connect SDK project, but it fails with an error like the one in the image. How can I make it succeed?
SEGGER...
I am doing something really really crazy, that's writing some application on PC using opcode serial port for configuration a light switch server (maybe light switch client...
Hey all,
I've been using the SDK for Thread for quite a while and got all the basic stuff up and running with Thread and the nRF52840DK, RPi Border Router, etc.
For example...
Hello, I'm working with nRF5340 DK with Zigbee communication. I'm getting RSSI values between 0-255, but I'm more interested in the value in dBm, so I would like to convert...
Hello,
I developed the code on nRF52-DK with Segger.And also I want to program this code to MDBT42Q chip with nRF52-DK.
What are the circuits and software programs where...
Hello, I' trying to use the Serial LTE Modem application on an Actinius Icarus board. I configured the nRF project for the correct target, enabled COAP support, set Nb-IoT...
After upgrading the nRF-Command-Line-Tools from 9.8.1 to 10.12.1 the RTT output of JLinkRTTClient stopped working when doing a nrfjprog --reset. Interestingly it still works...
Hello, i've tested dfu process from secure_bootloader with different app examples with success (ble_app_blinky, ble_app_uart, even a custom application) but, when I try the...
Hi, I want to use normal GPS data (not AGPS) to send to my MQTT server.
I work well with MQTT_Simple to send sensor data to my server.
I see a GPS example in /nrf/samples...
Hello,
I have application that is sending data over BLE every 5 minutes.
I want to implement DFU using BLE. I don't have any single button on my device.
What should...
In the software NRf Connect Desktop.
The packet length (bytes) variable. What part of the Bluetooth packet does this change.
How does one calculate the number of transmitted...
