Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello Nordic support,
In case of using concurrent multi-protocol (BLE + ZigBee or BLE + Thread using time-sliced mode) on Nordic devices (especially nrf52840), are there...
Hi,
Does the nrf5340 perform any integrity checking on the QSPI on-the-fly decryption? Are there any details available on the specific algorithm used? The datasheet only...
Hi, my question is about the commissioning of the thread protocol. Not so long ago I created an ish on the github of the thread project, but with software errors I was offered...
i use nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10056_ble.
The rom space is only 0x6000 bytes, I need 0x8000 bytes, how do I need to modify it?
I found some information in Case ID: 251716 , however, when I went to look for these options in the nrfutil manual there is not a single mention of what the options are for...
To the kind attention of Nordic support team,
we are experiencing a very random and rare loosing of existing ble bonding infos (device side). So that to reconnect to the...
We are getting a "No SOURCES given to target: drivers__ipm" error making build fail for our custom board when trying to move to 1.5.0 for official nRF53 production support...
Hi,
I am using NRF52832 with SDK 15.0, SDK Mesh 4.0.
As my knowledge, the OTA speed of Mesh DFU is very slow.
So can I use SDK DFU for faster speed?
Thank you.
Hi
Followed all the getting started instructions given here
https://nordicsemiconductor.github.io/asset-tracker-cloud-docs/v1.5.x/docs/aws/GettingStarted.html
and...
Setup :
Device: nRF52840DK PCA10056
Software: NCS v1.3.99
What I am trying to do:
I have 3 SAADC sequences that I need to run for my application that I wish to poll...
HI,
I'm using the zigbee CLI example as coordinator and have another CLI device for reference as router. With my sniffer I can log the association sequence with the cli...
Hello,
I have a nrf5340 PDK .
The kit does not work right, because i got a several errors.
For example in nrf connect v.3.6.1 the PDK is shown as 000000123456 also in...
Hello Nordic support,
I would like to confirm whether nrf52840 supports only Bluetooth 5.0 features or does it also support Bluetooth 5.2 features. If it supports Bluetooth...
Hello, I am working on Nrf52 mesh network and need to update device via any host mcu or flash connected with the nrf52. But could not find any way to implement it.
If anyone...
I have changed our code that has been running on v1.4 successfully to v1.5
Mainly because I'm hoping for an improvement in the reliability of the new modem library.
However...
