Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
Is it possible to upgrade a S112 v6.1.1 softdevice to the S113 v7.2.0 softdevice using BLE DFU?
I am getting the following error right after the SD + BL has been...
Hi folks,
I am playing around with the A-GPS sample.
I am trying to send the fix every five seconds to the cloud. This should be possible according to the webinar last...
At my system (production) there are 6 serial ports and 2 programmer (ARM-Flasher from Segger) connected.
The nRF Connect - Programmer only display 5 COM-Ports and NO Segger...
Hello,
I am starting a new project and we are using the following:
-NRF52840
-SDK v16.0.0
-pca10056 (NRF52849 DK)
After downloading the SDK, I was able to build...
Hi,
I am developing on nRF52840 using SDK version 15.0.3 and Softdevice version 6.11
I have observed that the once you initialize the app_uart using 'app_uart_init(...
Hi,
I want to identify the specific provisioned node among all n number of provisioned nodes using nRFMesh app.
Does any event will be appeared in sdk, after provisioned...
Hi, I am begginer, I work with SES, Mesh_v5.0.0, nRF5_SDK_17.0.2, and s132, SD v7.2.0. I started it two weaks ago. :)
I tryed the examples, Light switch , with server and...
Does Nordic have an example SW for transmitting and receiving data in BLE 5.2 connectionless isochronous communication mode? Is there a SoftDevice that would support this...
Hi, good morning , i am just wondering is it possible to send and recive data through ble faster than the coded examples please as i am sending gyrodata and its taking about...
Hello - I've google'd around a bit on this unsuccessfully...
I've successfully provisioned and configured an nRF Mesh network with mutliple servers and a single client,...
hi, I am working on the nrf52832 device, I have implemented the push button and I am able to detect button push and release but I want to notify the app when the push button...
Hi,
I am trying to interface nrf52832 with LoRa transceiver module sx1262. Can anyone please provide some sample code to check basic Tx/Rx of this chip. I am unable to find...
Hi,
I am looking for an example that uses the eDMA with the TWI in the 15.2 SDK on nRF52840.
My idea is to read out an external sensor using the TWI with as little processor...
Hi,
I would like to know how to set the service to NB-IOT Cat NB1,
and how then to set the UL subcarrier spacing to 3,75 KHz,
and how to fix the power to 23 dBm, not...
