I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
hi,
we are trying to add third sensor to the multi sensor example , new sensor is of type binary_input (0x000F) ZB_ZCL_CLUSTER_ID_BINARY_INPUT.
We are unable to subscribe...
I use nRF Connect for desktop / Bluetooth Low Enery Apps + nRF52840-DK.
When run 'start scan', In rare cases, very small RSSI values (-103dbm, -104dbm ...) may be reported...
I have brought nrf52840 preview dk ,it is not getting detected by the computer nor its power led getting light up. Last code i tested on its was blinky.
I doubt it has any...
I have a custom board that I have programmed using the UART_BLE example. The code executes and I know I am advertising since LED1 blinks meaning it is advertising but for...
I am testing the Sensor example in the Mesh SDK.
For my implementation I need three properties that are given by the BT Mesh specification. (Properties 0x004F, 0x0057, 0x0059...
Hi everyone!
I'm running my Nordic Thingy 91 with "thingy91_nbiot_legacy_pco_dfu" and it works great!
Now, i want to make some specifics editions in the main code in order...
Hi, We are developing an application that should receive commands via SMS. The device runs on a fairly large and rechargeable battery so the power consumption is not the most...
Hello DevZone,
PCA10040 SDK 15.0.0 SD132
I written my own SPIM driver which uses the list function to read in a few bytes. I've set up my list as the example in the...
Hi,
What is the difference between performing a reset by using the function sd_nvic_SystemReset(), and performing a reset by turning the power voltage off and then turn...
I used "nrf5_SDK_for_Mesh_v4.2.0_src.zip" and "nRF5_SDK_V16.0.0", When I used scan_start() command, I saw Light_Switch_Server device and Light_Switch_Client device on the...
We have fabbed a PCB for the nRF52840 that has a QSPI chip. The pins are different from the example in the SDK. I was trying to get the SDK example (examples/peripheral/qspi...
Just test SDK17.0.2 serial DFU demo project on Nordic PCA10100 board by USB serial.and use s140_nrf52_7.2.0_softdevice.hex
Got below exception. Any clue for it please? ...
Hi,
I have my application based on nRF52840 device.
When writting a wrong passkey, my device is reseted.
Which can be the reason? I have already implemented event PM_EVT_CONN_SEC_FAILED...
Hello
To calculate the definite yaw value of gyro, I would like to use the mpu9250 with magnetic sensors. I used Martinsbl's nrf5-mpu library when I used mpu6050, can I...
Hi there,
what is recommended strategy to read/write data on uart?
Taking from sample, read byte-by-byte, on 115k, sometimes data are truncated.
Is there a possibility...
