Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I am trying to better understand the eSIM provisioning process. I want to verify that the IMSI changes to a local profile after the first registration with the provisioning...
Hi Nordic Devzone readers,
Recently I've picked up a NRF9160DK and have tried to program my own user program onto it. This will consistently fail unless I hold the reset...
Hi,
I am using the BMD340 module from Rigado. The module is connected to a raspberry compute module via UART. The design implemented is the “CLI co-processor design” where...
I have downloaded ADC example to the board nrf51422. I could not figure out how to give analog input and view digital output. please help. Thanks in advance...
To the kind attention of Nordic support team,
I'm using sdk 15.2, I'm working on usb hid composite example, and I modified it to have it scanning a big input keyboard matrix...
Hi,
As we know,we can modify the Mesh params though the config model, but when we actually installing and deploying ,If we want to improve the reliability of the Mesh network...
I try to bring an old Project (2017) back to life and use the new SDK 16
the Code usese BLE_GAP_TIMEOUT_SRC_ADVERTISING, but that is removed in the new SDK version,
what...
51822
SDK11
Can we change the advertise interval after 51822 started? I need to change the interval to lower / higher based on the user phone. For example, if its IOS...
How does Broadcast characteristic property of GATT can allow BLE observers devices to read the data without being connected with the device? Does this mean we share data without...
We recently ported to the nRF52832 and our electrical engineer had to make a couple changes from the reference design due to space constraints. The port has worked well during...
Hi! I'm trying to measure the voltage drop across a custom PCB we're developing. This was done while trying to get a clear sense of the current consumption used by our board...
Hi , I am using nrf52832 and try to implement a high throughput in ble5.1. i interface memory with nrf52832 my task is to read the memory and send the data to the app with...
Hey Nordic Team,
I noticed an issue with the SDK and `nrf_serial.c`
After deactivating all legacy code and removing all references to standard UART I noticed that I was...
I need a UARTE driver that does a few things differently to the provided UARTE driver and hence I am writing my own based on nrfx_uarte.c . At the moment I am testing the...
