hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I am trying to use the LPCOMP API, but I am having trouble with the following function:
nrfx_err_t nrfx_lpcomp_init
(
nrfx_lpcomp_config_t const *
p_config ...
I'm attempting to setup GPIOTE for an output that is set and cleared by different events. The GPIOTE driver doesn't let me initialize an output twice. Is there a way to do...
I have 2 objectives BT beacon and concurrent ESB with Thread using time slotting A. I would like my thread devices to broadcast BT beacons. As this does not require any reception...
Hello. We have product based on NRF51822 chip. 24 bit 4 channel ADC connected through SPI to MCU. Data rate is 250 Hz (4 ms). We send two ADC samples evry notification packet...
I started setting up Zephyr SDK development on my W10 laptop, according to the nRF Connect for Desktop guide, but running into this error when executing pip requirements installation...
Hello,
I'm writing a BLE app that acts as a peripheral and a broadcaster. If a connection is established, I'd like to continue advertising but update the advertising parameters...
Hi,
I am migrating sdk 15.2 to 15.3. Everything works fine, except the nrf logging. Currently, I am using RTT configuration, with default backend enabled. The code is simple...
Hi,
I have been using the PCA10040 and PCA10056 development boards to do some evaluation/testing of the Nordic BTLE radio functionality. We now have purchased standalone...
Hello,
Ive been trying to get simultaneous GPS reception and LTE connectivity for a while now. I've read that this wasn't possibe in the past but it looks like it should...
Hi in the code below I successfully register multiple custom services (m_cus and m_cus2) using NRF_SDH_BLE_OBSERVERS(). In my original code when notifications is turned on...
Hello,
Tried the 2.0 nRFSniffer hex file today. It does not show up in WireShark like
the Beta 3 version does, "nRF Sniffer COM6". Tried on two devices with the same result...
My application just hit the following fault randomly:
I tracked back in the map file and that is inside the Nordic NRFX library in ipc_trace_handle, so I have no source...
Is it possible to have discontiguous Non-Secure areas in SRAM to be used by the application?
&sram0 {
reg = <0x20000000 DT_SIZE_K(8)>;
};
&sram0_ns {
reg = <0x20002000...
Hi There
Here we have been encountering some problems and would appreciate if you could help.
We are designing the hardware based on the following schematic, please...
