There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi there, we use the nRF52840 on a embedded system. The nRF52840 is connected via usb interface to the central cpu of the embedded system. An embedded linux (buildroot) is...
Hi!
Is it technically possible to implement performing of unmodulated TX carrier transmission by a write to some BLE characteristic? If yes, then from what to start?
Thank...
Hi,
I am trying to use the Bluetooth low energy capability of the nRF9160 DK (nRF52840 chip) by using the lte_ble_gateway sample from Nordic. After changing some lines of...
Hi
I'm using ZigBee light control coordinator example in "nRF5 SDK for Thread and Zigbee v3.1.0" on nRF52840 evaluation board.
when it will execute bdb_start_top_level_commissioning...
I am runing the light switch example in zigbee sdk v3.1. I am connecting to a smarthings hub. I have set the a single change on the code:
The device will be connected...
A couple questions about the nRF52840 GPIO Electrical Specification:
1. In the nRF52840 GPIO Electrical specification, VOH at 0.5mA is spec'd to go as low as VDD - 0.4V...
Hello,
I have been using the development kit for more than a month when after one flashing, the LED 5 on the board started blinking at one second intervals and the board...
I read a nRF9160 DK 0.8.5 circuit design and have a question about the GPS circuitry. What will happen if I bring the LTE antenna closer to the GPS antenna and reduce the...
Hi,
We have a program that uses the radio driver for IEEE 15.4. Currently we do not need Bluetooth and IEEE 15.4 working simultaneously but we do need Bluetooth DFU. When...
Hi,
Just spent a while debugging this and since there seems to be nothing - well I can't find it anyway - up here thought I should document this issue. This relates to SDK...
hi ...
i am using nrf toolbox (ble uart )to receive data from nrf52832 ..i am receiving the data for every one minute . i am facing the issue in auto connect see the below...
Hi,
Actually I am interested in making the custom design Board for the nRF52 series , so where can i find the schematics , layout files of the nRF52 Development Kit ....
Using s140 for the nRF52840 is it possible to have a BLE multilink connection (up to 8peripherals) with an extended MTU size (around 70bytes)?
All examples that I have seen...
Dear Team,
would a solution like this be possible with nrf91? http://rxnetworks.com/location-io/predicted-gnss-ephemeris/
> a reduction of Time-To-First-Fix from 45...
Hello!
Could you show me an USBD configuration example which works fine with Arduino serial monitor? Because Arduino serial monitor froze when i send a string , but when...
