Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello,
I am using nRF52840 DK for bulding a bluetooth mesh. I would like to use JLink in board kit to flash and debug for other nrf chip.
How I can connect and configure...
Hi,
I'm using SDK 15.3. How do I connect a central (nrf53832) to another central (phone/laptop) using multilink central example? Its only connecting to other peripherals...
Using the 15.2 SDK, the stack generates an error when attempting to bond. I am using the android nRF Connect test app to initiate the bonding after connection. The error generated...
I'm using SDK 15.2 & HID keyboard example. I would like to know the following things-
1. How long does BLE chip advertise its name before making a connection with central...
Hello,
We're currently preparing for BLE certification of our device. It contains an NRF52840 on a custom PCB, so I believe we'll need to perform RF-PHY testing for certification...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
Hi! I develop board based on NRF52832. P0.08 is connected to the MOSFET transistor.
The transistor switches the relay. During start (power on or reset) on GPIO there is...
Hello,
Please let me check about the usage of an IRK for the default setting and how to change an IRK each bonding cycle.
We use the resolvable address for our application...
Hello
I have a setup with 3 nrf6310 dev kit and with a nrf24LE1 module on each of them.
1 acts as a transmitter and the other 2 act as a receivers. What I specifically...
Hi
I am using nrf52 DevKit and was able to load the \examples\ble_peripheral\ble_app_beacon program on it. I am able to see the beacon RSSI, major and minor values. Now...
Hi,
I am using Nrf Sdk Mesh V3.1.0 with softdeviceS132 and sdk board Nrf52832
I am trying to implement Normal DFU in Mesh network.I don't need Mesh DFU.
So i have added...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) I am bit confused between fds_record_update...
Hello, I am using AES -CCM encryption in my program. I want to know about memory like does it need any dynamic RAM ? In example code I found 'nrf_mem_init()' but unable to...
Using: NRF52832, SD 132 6.1.1, SDK 15.3.0, Mesh SDK 3.1.0.
Hi, I included mesh_opt_core.h in a C++ file, and got compiler errors at NRF_MESH_STATIC_ASSERT().
I fixed...
