Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello! I am having issues dfu from the huawei p30 lite. with nrf51. Tried with nrf connect and nrf toolbox.
Dfu progress stops at 2-3% when uploading. Error Remote dfu error...
I am unable to connect the nRF9160DK to the cellular network.
I have gone through the "Get started guide" (working in Linux) and I have been able to install the SDK. I have...
Hi, we have faced with the same issue as many nRF52 users, debug interface (DIF) will stay active after flashing and high (~3mA) continuous current remains, Power cycle will...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
In BLE peripheral example ‘ble_app_template’, it is for doing Advertisement...
hi... folks
I am working on multilink central example, i have modified this example to multi link central uart ,where i can able to connect to multiple peripheral to a single...
Hi,
I am using NRF51822(PCA10028) ble_app_uart example , I need to change the name of the BLE device during Advertising and store the name in Flash so that when ever the...
Hello,
I am trying to establish a network to send data over the boards.
I tried using examples in Ble_central and Ble_peripheral, but in those examples they would stay...
Using the esb tx fifo, it appears to change the ESB_MODE from PTX to PRX, and changes the esb channel to some other value. Is there any way to setup the radio so that it doesn...
Hello,
I am working with nrf52840. I have read how the SAADC example works at https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v13.0.0%2Fnrf_dev_saadc_example...
Hi everyone, I'm having trouble deciding on the "best" / "most sane" way to interface two I2C sensors with the nRF5832. Both sensors are on the same I2C bus. The first sensor...
Hi Bro
I have a project need to use BLE + ESB Concurrently, actually I have did it in my previous project
but seems it has problem in new SDK
In my old project: SDK11...
I'm using the nRF52 DK (with an updated firmware) to program an external target (using the "Debug out" connector). It looks like the programming speed is limited to 1MHz:...
HI,
I am seeking help in getting the only peripheral code from the ble_app_mtu_throughput. Actually, I want to use the only peripheral code in my and want to use the maximum...
I have multiple sensors. I would like to ask if there is support for linking 4 or even 4 Bluetooth devices at a time.
My ultimate goal is to connect 4 or more Bluetooth...
