hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
While developing code for our custom board, we ran into a filesystem corruption issue with fatfs+qspi block device and multiple directories. We were able to reproduce the...
I have problems running the ble_app_uart_pca1004e_s112 on a custom nrf52810 target devivce. The custom nrf52810 target is a custom board with the Rigado BMD 330, which is...
Hi there,
Please see the video for a full run down: https://www.youtube.com/watch?v=nIeIUMutBlU
Basically, I have a perfect and verified design that's been in the...
I'm using python code based on the heart_rate_collector.py example in pc-ble-driver-py to scan for devices and connect to a peripheral device.
This all works fine, except...
I have an existing Firmware (build on Crossworks) that has correct "floor" power consumption (< 10 uA during sd_app_evt_wait() on my setup).
I migrate my code to rune with...
I am stuck with strange behavior of s140 softdevice version 6.1.0 and later for ble_app_template example on nrf52840 preview dk(pca10056).
As I am planning to remove LF...
Hello,
We need to produce a driver for the ST25R3911B NFC chip working with NRF52840.
We just need to read NFCA tags so we thought that the example nfc/tag_reader included...
Hi i am using SDK15.2, nrf52832 board.
Which function is necessary to achieve multilink in example code. I dont understand how the central is connecting multiple peripherals...
I just purchased this unit and followed the setup instructions. I did not perform any flashing. When I plug the usb into the computer the jlink drive doesn't show up in Windows...
Hello, I am not sure if this was noted before. I didn't find anything about it. This is more of a suggestion. I was looking to use Thread CLI Example to use with the pca10059...
Hi,
I am using a custom board with the nrf52810 and trying to interface with the SHTW2 sensor. The sensor has an I2C interface and hence I use the TWI peripheral for this...
Hello,
I have a question regarding BLE_GAP_EVT_CONN_PARAM_UPDATE (nrf52840, SDK 15.2).
I'm evaluating the BLE_UART example using multiple peripherals. The goal is to scan...
I have an nrf52840 that the fds_init function is returning an error 11 (NRF_ERRO_INVALID_DATA).
What would be the most likely cause of this?
The code is based on the THREAD...
