Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello,
Our setup:
IDE : Segger Embedded Studio for ARM V4.12, nRFgo studio
SDK : nRF5_SDK_15.2.0_9412b96 + SDK for Mesh3.1.0,
Softdevice : 6.1.1
Computer Platform...
Hi, I'm using SDK12.1 example ble_app_ancs_c.
Is it possible keep advertising (non-connectable is ok) when ancs connecting?
And how to do it?
I tried call advertising_start...
Hi,
I have been having issues with the compile hex files I get when following the steps to build the pc-ble-driver (). While I am able to build the hex files when I place...
I got Orange sim connected to LTE-M network on nrf9160 DK, verified it on LTE link monitor. But when i tried adding a LTE device on nrf connect cloud, i am not able to register...
Hi,
I tried to build the lte_ble_gateway sample in SES, however it gives the error below regarding the UART.
Any suggestions how to resolve this issue?
Hi,
As mentioned in the subject, I am confused with the SPIS example from nRF52 SDK 15.3.0. I wonder where NRFX_SPIS and _INST_IDX are defined in the header file?
SPIS...
Hello,
I am testing the Light Switch example and I observed a problem:
- I noticed that it was possible to reset the "server nodes" by pressing their "button 4" to leave...
I am having an issue migrating some code over from Keil to an example in SES studio.
The code in Keil is simply listening for a radio packet, when it receives it, it transmits...
Hello,
I generate a private key by using nrfutil.
I like to convert raw data format to use in the code from private key.
Additionally, I already used a nrf_crypto_ecc_key_pair_generate...
I want to drive a servo by the PWM on nrf52832. The pwm cycle is 20ms and the duty is 1.5ms. But i have a problem that the duty is not precise when the BLE is working. I need...
Hi,
I am using a Sparkfun nRF52832 Breakout board with the Arduino IDE. My objective is to control 3 SPI digital potentiometer. The problem is I don't know how to select...
nRF52840
SDK15.3
My question is regarding the low frequency clock.I am initializing the low frequency clock as follows:
When TASKS_LFCLKSTART is initiated in line...
Hi Nordic,
I have been trying to communicate with KX 124-1051 using IIC in nRF52832 . I am getting NACK from slave every time i send the device address. I checked all the...
