Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello All,
I have 2 evaluation boards nrf53840 EVB "PCA10056".
I would like to run on them the "ble_app_uart" in "nRF5_SDK_15.3.0_59ac345" as following:
A custom board...
let say i have a temperature sensor connected to one nrf 52840 dongle of a mesh network. Now can i make the Led of all the dongles glow if the temperature increases the given...
I downloaded the latest nRF5_SDK_15.3.0_59ac345 and some other old versions of SDK documents. (I am trying to use pca10040 development kit to program Fanstel EV-BT840F, aka...
Hi
One of our customers have complained, that our sensors are making occasional errors.
I have looked at it, and they are correct. About 1 in 8 Million packets send...
Hi, I have my custom board for the nrf9160 ,
I was able to program it through the built in programmer of the nrf9160 dk but I have an issue, when I connect the VDD to the...
I'm using adafruit_tag_reader example to read ISO14443 tag. When I put a tag near scanning area of PN532. It reads tag multiple times till I remove that tag from there.
...
Hi!
I am using IAR compiler for my project
I declare global variable
__no_init u32 uPowernResetSignature;
in my code I assign value to this variable
uPowernResetSignature...
Thank you for taking time to look at my problem!
I have managed to combine the TDK/Invensense library for their IMU MPU9250 within the SDK 15 utilizing simple TWI calls...
Hi,
I have nRF9160-DK kit and its environment is set such as nRF Connect SDK and Segger Embedded Studio.
I want to build a simple application from scratch for example...
Hi, I am trying to modify UICR PSELRESET but its not changing. Any help?
NRF_UICR->PSELRESET[0] = 0xFFFFFFFF ; NRF_UICR->PSELRESET[1] = 0xFFFFFFFF ;
Thanks
Hi,
I'm developing an application using the timeslot API for a custom radio protocol. The application also uses a number of the nRF52832 peripherals, as well as the app_scheduler...
Hello,
I'm having an issue with scripting AT comands directly into the code of the nRF9160. I'm a novice at all this so I apologise if the mistake is an obvious one.
Inside...
I get "ERROR: There is no debugger connected to the PC with the given serial number." when I run e.g. nrfjprog --eraseall on command line.
Programming/debugging using VisualGDB...
Hi,
The User Guide v1.3 in Chapter 2 (minimum requirements) states "SEGGER J-Link Software" under "Software requirements". Is there J-Link software specifically for use...
I've been developing firmware for the nrf52840 for a few months using armgcc+openocd+arm-none-eabi-gcc working successfully. I recently upgraded my ubuntu version (18.04)...
