Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
I have bought nRF51-DK and have downloaded the hex file successfully in the mbed mode, I wonder May I debug the DK with CMSIS-DAP instead of JLINK? I searched the internet...
I just finished reading the O'Reilly book " Getting Started with Bluetooth Low Energy: Tools and Techniques for Low-Power Networking " where the author uses the nRF51822-EK...
I could run the examples like blinky just out of the box
But, I am clueless how to add a bootloader to this example. I just want to add a simple bootloader from Open Bootloader...
Hi,
we are about to enter bluetooth and expand our products with it. however, the approval process still raises some questions. What I have understood so far (please correct...
Hi everybody,
as already mentioned in the title, I guess to have stumbled across an incompatibility between the app_pwm library and the gazelle link layer.
To keep it...
Hello,
I'm using SDK 15.3.0
I added "err_code=sd_ble_gap_adv_data_set(p_data,31,NULL,0);" to the advertising_init(void) function, but I got the following error:
Error...
MCU: nrf52840
SDK: V 15.3.0 with nRF-IEEE-802.15.4-radio-driver
problem:
I tested repeatedly connection with my nrf52840 production (peripheral) with andorid phone...
Hi,
I have downloaded MDK Keil software .so the problem is if i click on + sign in all devices in pack installer it is not expanding and also i am getting like this
if...
Hello All,
Greetings!!!
I am working on nRF51822. I am used custom board. For reference i used nRF52 SDk 8.1.0 in IAR.
Right now i am use gpio pin as an interrupt pin...
I send 25 byte long messages to unicast addresses in a Mesh network. Because of their size messages become segmented. access_model_reliable_publish() is used for sending....
Hello,
I am using a combination of several Nordic devices and hardware. The nRF52832 is used in a sensor to collect light level information. That data is transported over...
Hello,
I wrote a simple program to turn on externally connected LED at Port 1 and Pin 10. But it is not working. See the code -
#include <stdbool.h> #include <stdint...
Is there any documentation about how to configure the SoftDevice clock configuration using the RC as SoftDevice clock source?
My target is the nRF52832 with the S132 Softdevice...
Folks,
We're wondering how the soft device can work with it being provided as a hex file? Usually with things like this you'd get object code to link to, but that doesn...
