Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I'm using the UART / Serial Port Emulation over BLE example on the nRF52 development kit connected to a custom microcontroller.
I just need the nRF52 to simply relay bytes...
Hi everyone,
I have been looking for information about this, but I have not been able to find anything. I would like to send data employing UART, but I can not use the...
Hi, I have a few general questions on nus_data_send().
First off, is there another known way of transferring an array/string via ble to the Nordic mobile app other than...
Dear Sir,
I am working with nrf52832, SDK15 and s132 soft device.
I am using RIGADO DK .
Is it possible to continue advertising(from peripheral device) even after...
Hi All
I am doing a project which is base on SDK15.2 examples\proprietary_rf\gzll\gzp_dynamic_pairing\host\pca10040\blank\arm5_no_packs
I would like to add a timer to...
Hello,
I cannot add SPI0 to my application because OpenThread library was built with it without any interest of that. Could you fix it please ? (I need the 3 SPI peripherals...
Hello! I want to use the start time of the XOSC16M in NRF24LE1. I got ~4 ms. Can I put the processor to sleep at this time in standby mode? How to do it to wait for wakeup...
Hi all:
I see the "ant_share_channel _master_to_master" example,
this example is share_master,
my question is,
How to get p_ant_message[]?
the p_ant_message[]...
Is the recently released SoftDevice - ANT/BLE S332 SoftDevice v6.1.0 - compatible with the recently released SDK v15.2.0 ?
The supported SoftDevices listed in the documention...
Hello. A re-connection failure problem happens on our products.
chip:nRF52832 SoftDevice:S132 SDK v11.0
1. pairing and bonding on LESC 2. reset connection and re-connect...
Hi,
I have connected and SPI flash module to my pca10040 dev board. I wrote a test cycle of erase/write/verify for the entire flash and it works correctly. My initial pinout...
Hi,
I need some very simple file system to use on an external SPI flash. I gave a quick look at Flash Data Storage and it should be ok for me. I am not sure though why it...
Hi,
Disclaimer - this is definitely a question where one picture worth a 1000 words... ;)
My app use timeslot api to get a free time period to do some hard real-time...
