Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello to everyone. I´m trying to configure the buttons of my SDK nRF52 to turn on LEDs, but all the examples I´ve found here are using BSP_EVENT_HANDLER. So, my question is...
Hi,
I am developing an application on an nrf52840 based custom board that includes a dfu bootloader. Currently this bootloader is the example secure one. This will be tweaked...
Hi,
I spent a lot of today trying to get or even to find instructions on how to get log messages (RTT) out of both the app and the bootloader I am working on. This was the...
Hello all!
I tried to develop a small BLE application and got stuck with endless loop in nrfx_uarte_tx() function (nrfx_uarte.c driver) which loops endlessly in these lines...
Hi, I am running Segger Embedded Studio (4.10a) to get used to the Nordic DK for the nRF52840. Now I have found, that the register display seems not to be able to show some...
Hello,
just a quick question for my understanding: If I use differential mode and have the Vp and Vn pins as an input channel to the SAADC, then may I only supply Vp with...
Hi,
I followed the example nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_buttonless_dfu to add DFU service into my 3 programs. One has HTS service, one has HRS...
I have a custom board with nrf52840 with cr2477 battery (1Ah capacity). I was download firmware to board and after a week the battery voltage dropped to critical. In the firmware...
Hello,
I want to access the nrf9160 over UART from other controller My main concern is to program nrf9160 to respond with at commands from external microcontroller. (Just...
Hi everybody!
I hope I am not too late to jump on the nrf51 train, but I had the ability to get a great deal on them so I really want to use them for a project we have....
I am facing a strange issue where I removed all code related to the app_uart from the UART example. Now the logs are being dropped. Anyone know why this happens?
Hi,
For a few days, the nrfcloud device screen is not showing the sim card total data usage.
The console shows this error:
Failed to load resource: the server responded...
hello,
i am developing a health care device and i am using nrf52 dk board for development , i want my device to communicate to the android app, and i have zero experience...
Q: nRF52840 DK does not appear as a removable drive named "JLINK" Steps I followed 1-Connected the NFC antenna to the board. 2-Used a micro USB 2.0 Data cable(Fully functional...
