Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi all
I'm using the NFCT peripheral of the nRF52832 Revision 1 and I'm facing the following issue:
When the reader sends the SLP_REQ, the NFCT receives an incomplete...
Hi, there
I want to remove the bond in current time service example, because the bond process make me less convenient when I debug. so I changed the code in peer_manager_init...
Hi using dev kit pca10040 and sdk 14.2.
I'm trying to use the dev kit buttons to stub out an ANT+ bike speed sensor. Essentially I just need a way to provide a speed reading...
Hello, i am using ble_app_uart example. i am trying to send A to Z from ble to uart. Has i noticed, it is transferring 20 characters at a time. to make sure that i add print...
I am using nRF5_SDK_15.2.0_9412b96. I have application data that accumulate in flash but can be thrown away before re-flashing new app image. I am thinking about instead of...
Hi,
I configured nrf_ble_qwr to use 256 byte long buffer in my BLE peripheral. I registered my value handles (2) which I want to support long writes using nrf_ble_qwr_attr_register...
Hi Folks,
I'm new at using the nRF52832 chip. I recently was handed a 3rd party board to evaluate and up until today I was able to use the nRF52 Development Kit to act...
Hi,
I am working on "nRf52832 - PC10040" based ISP1507/. I have already adapted the peripheral/spi example of SDK 15.0.0 to my needs. Now, I want to merge this spi example...
Hello,
With Segger ES I am able to compile and run the Blinky example (pca10040, S132) from the nRF5 SDK without any issues, it loads on my nRF52 DK board on and it shows...
Hi,
I'm working on a project where I need to collect and process analog data coming from high speed sensor measurements. The data needs to be read at a speed of 25k samples...
Hi,
I am trying to convert the string from ctime to a struct but i always get garbage values if i use "uint8_t". But i can get correct values if i use "int" datatype....
Hello Nordic
Bluetooth SIG had released their new bluetooth core specification 5.1 with new feature is " Direction Finding ".
I know that all nrf52 now support BLE 5.0...
Hi,
I'm using the NRF52840 PDK version:
PCA10056
0.11.0
2018.3
With SDK version 15.2
I've been trying to develop an application based on the HID Generic example...
Hello,
My configuration:
Windows 10
nrf5SDKforMesh 3.1.0
nRF5 SDK 15.2.0
nRF5832
My goal is to merge the UART and Mesh example. I found your example ble_app_uart_coexist...
