Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
Is there no specific code of ble_app_uart_coexist meant for PCA 10056 and eventually s140?
Or will the same code work for the nRF52840 board?
I am using SES and...
I want to use the nordic USB peripheral drivers to allow for the initialization of multiple devices. The end result of the project will be to have a single nordic creating...
I am using the nRF52832 (on Rigado BMD-300 EVAL kit). I am using keil IDE and nRF GO to upload my compiled code to my device. I am using SKD 15.2.0. Using Windows 10.
...
i donot know why,because other board is ok.
i am using this project
\nRF52832 pack\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_uart_c...
I am migrating my project from SDK 15.0 to SDK 15.2. I was using CC310 to accelerate crypto in the bootloader.
While builiding the bootloader wit SDK 15.2, I got the error...
Hi team, Does the nordic chip receive a Bluetooth signal being communicated with a mouse, keyboard, cell phone, etc., and the sleep state (sd_app_evt_wait()) is canceled?...
Hi,
Can we use BLE 5 beacon with BLE 4 scanner?
As BLE 5 is long range which is my main concern. So, can I get that long range with BLE 4 scanner?
Thanks,
i have done the 10 dfu steps in DFU quick start guide when the boards are not far from each other it works but when i make them far a little
i mean one device in the area...
I am using a Sparkfun nRF52832 breakout. I was trying to install the Softdevice settings onto my Arduino IDE once I clicked on tools -> "nRF5 flash device " the blue ticking...
Current consumption of my code running RTC from LFCLK is ~2.5uA from the power profiler when I set the register values as. NRF_POWER->RAM[2].POWERCLR = 0x01; NRF_POWER->RAM...
Hi,
Currently evaluating SDK and have some issues, I would like to run some demos.
I believe I've managed to erase the "preconfigured" Firmware on the SDK, I have tried...
I am working on SDK-15.2, nRF52832 Dev board. My question is how to add write protected characteristic by KEY? Mean when we want to write something from peer device (smartphone...
1. I've noticed while using tools like NRFConnect that most BLE devices in my proximity do not include the device name in the advertising packet. My assumption is the developers...
Hello, I am unable to connect thingy 52 with my laptop, I have NRF connect v2.6.1 installed but it is unable to find thingy.
Thingy is not connected with any other device...
