Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
I am working on implementing the USB HAL for the nRF52840 for Mbed-OS's upcoming USBDevice feature release. I am trying to get my implementation to pass all of Mbed...
I haven't been able to find documentation for the RTC or RTCs on the 9160. I want to know what the drift is and which RTC timers are available in various stages of sleep when...
Using this sheet
https://www.sparkfun.com/datashe...
I'm trying to figure out two things.
1) There is a section on timing but I'm a bit confused what SPI Clock rate...
Hi, I'm just a beginner with Bluetooth. I want to make a simple bluetooth module, so I just bought nRF52832 and other devices like capacitors, inductors, crystal oscillator...
Dear nordic,
I want to add long range in my application and also i want to set maximum power
i used sdk 15 and example ble central and peripheral(relay)
Where i set...
I have been working successfully on both PCA10040 and PCA10056
I want to work with NRF51822.
When I look at my sdk I see no folders for my PCA10028.
I see folders in...
Hello,
I have read numerous posts about NRF_ERROR_CONN_COUNT but yet able to solve this solve, my setup is NRF52840 Dongle as central and I want to connect to multiple Heart...
Hello! We are trying to transfer the data between two nRF52840 development kits through NFC. Is doing so possible without using any other reader hardware? If not, then we...
I am using SDK13 with a nRF52832 development board.
When trying to compile the Multilink central example with gcc and I am getting the following error:
../../../../.....
I'm just a bit confused on how gpio detect works. After setting the sense config for input I realize that a change in voltage will trigger a sense signal that will create...
I mange to identify and provision the Light switch example on the PCA10059 Dongle and fanstel gateway with no problems. IT use to work on my PCA10056 DK but has for some reason...
I am using nRF52 SDK v15.2.0, nRF SDK Mesh 3.0.0, and Segger v4.1.2.
I am trying to add the proxy service to the client node of the BLE_UART_COEXIST example. Has anyone...
Hello all
i have problem with doing this example
https://github.com/gamnes/nRF52832-buttonless-dfu-development-tutorial
Here is my stepts to do this
1.Download Sdk...
Hello
We start working with Zephyr and nrf52840. What is the right way to overwrite values defined in nrfx_config_nrf52840.h with Zephyr? The NRFX_CLOCK_CONFIG_LF_SRC is...
