Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Using SDK 15.
adc_read works properly in main loop.
When called from an APP_Timer or from BLE connect event, function hangs. I set a breakpoint at the handler, and breaks...
The documentation states, “Only one data pipe can receive a packet at a time”
So what is the minimum acceptable delay between the receipt of two packets to two different...
Hi,
I have gone through PPK user guide but it is not working out.
In my setup I am using
One DK as external SEGGER JLink
One PPK as standalone power profiler
One...
Hi,
I want to interface wifi module(for example ESP8266 ) with nrf52832.
I need to transfer some data (received through bluetooth) to cloud(AWS).
Can I expect esp8266...
I have been trying to get the Timeslot API working with v15.0.0 of the nRF5 SDK, and have not had any success. All of the examples that I can find are built for much older...
I'm trying to implement the HID service on a custom nrf52832 board, unfortunately I'm running into problems.
Here's what happens: Advertising, connecting to the board,...
Hi,
I think I already know the answer but just to be sure, there is no difference on using printf (with added retarget library) and the app_uart_put() since printf will...
Hi, This is what constant carrier looks like at 2450MHz on my custom board using DCDC disabled
This is with DCDC enabled:
It can also look much worse with no real...
Hi there,
I'm looking at porting (i.e. re-implementing) an Arduino project to the nRF52832 to take advantage of the s212 or S332 softdevices. This chip is a few orders of...
I want to created a connectable iBeacon with nRF52810. I would like to connect my beacon through an app like nRF Beacon app and would like to configure....
* UUID
* Major...
Trying to run the SPI Master application on a custom nrf52382 based device (custom PCB) to communicate with an ADC chip that is taking analog values from a Multiplexer. Not...
I've designed a custom board for the NRF52832. Current consumption is not a major concern, and the pin location was convenient, so I wanted to use P0.00 and P0.01 for I2C...
Hi,
This is a problem report for the Programmer App v1.0.1 on nRF Connect v2.6.1 on MacOS 10.14.2. I have been attempting to use the programmer app with the nRF52 Dongle...
Hi all,
I have a trouble. I use 2 Dev Kit NRF52832. Flash light switch server proxy and light switch client proxy. Issue is when I erase and flash the first time, Client...
