Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I'm currently doing a current consumption test for bluetooth mesh using PCA10056. I want to label the plot like the ones in Online Power Profiler, but it turns out I...
Hi. Does anyone know where I can download the CDC ACM diver for windows 7?
I am running the example on the nRF52 dev kit, but I get an error as windows can't find the driver...
Hi all,
I'm currently implementing a Bluetooth Mesh system for testing various network characteristics.
I am running some tests were a Nordic Thingy:52 is sending a lot...
Hi, I have read the "nRF91 AT Command Reference Guide v0.7" and I would like to propose a new AT command to be added and also an additional feature to an existing AT command...
Dear nordic:
I am confused of NRF51824 MTU issue, NRF51824 can use S130 softdevice, S130 is qualified bluetooth 4.2 core spec, then why S130 features don't included MTU...
While trying to find out a realistic maximum power consumption target I was searching for the power consumption of the LPCOMP comparator. I've seen a few claims about 0.5...
Hello,
I want to send data from central device to peripheral device. I am currently using nRF52DK.
While sending data from peripheral to central device, data is sent successfully...
hello all,
I buy the Fanstel EV-BC832 V2 and start to paying with it.
I used the IAR ide and Embedded studio (SEGGER) ide for my tests.
First i check the blinky and...
I development nRF52832, I want change mac address.
So I modified nRF5_SDK15.0.0/examples/ble_peripheral/ble_app_uart.
I added code to the examples.
////////////////...
Hi everyone,
I want to program the nrf51822 module with the discovery board stm32f429i-disc1 through ST-LINK programmer in Keil IDE but this error appears: "ST-LINK connection...
Dear DevZone Team,
I am an absolute beginner in the field of mesh networking and hope you could help me getting started. Please bear with me.
I have a bunch of sensors...
Does anyone uses Sloeber to program nRF52? I have an issue, when I add a header nrf_temp.h to the project and using following functions:
The problem appears when I add...
Dear Nordic team,
We are developing a BLE application for IOS and Android. On Android, we utilized your Nordic Scanner Lib to scan Bluetooth devices and it is fine and...
Hi. I am trying to stop advertising after a delay in the UART example using;
sd_ble_gap_adv_stop(???)
What do I put in the brackets? It is asking for a uint8_t called...
