Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Using nrf5340 with nrf70 on a custom board, using NCS 2.9.0 (and I can't/won't update to 3.2.x as the nrfx4 update breaks all my code)
I want to use the wifi interface to...
I have an application in which there are two high speed sensors consider it as sensors 1 and sensor 2. Both sensors are connected over same SPI lines having different CS pins...
Hello,
For the vias in the exposed pad of the NRF54L, I've read that ideally, the vias should be capped and filled. However, due to trying to minimize cost, I was wondering...
Hello everyone,
after some months, yesterday I used my PPK2. When I plugged in and I opened the Power Profiler App, a pop up required me to update the device firmware. ...
Hi,
We had a nRF52840 DK board developed off Hardware files v3.0.3 build. The manufacturer didn't have any of the MCU or SEGGER J-Link debugger files on the device. We are...
I added a cmake configuration option to CMakeLists.txt, but sending a value through west build does not set the cmake option. Here is what I have done: CMakeLists.txt
The...
I am using an nRF52840 dongle as a sniffer to capture BLE packets in Wireshark. Recently, I’ve noticed that the captured files are approximately half the expected size, and...
Hello,
my nRF9151 DK appears to be damaged or has a power-path failure.
Current symptoms:
No LEDs light up
No J-Link is detected
No COM port appears
No mass...
I'm stuck implementing encrypted firmwares on the nrf5340, ncs 3.0.2., with NSIB and MCUBoot. I got signed DFU to work as described in Exercise 3 – DFU with external flash...
I noticed from the design guide that the voltage tolerance of capacitors C3 and C10 is 10V. Can I choose 6.3V for the voltage tolerance of these two capacitors? Will this...
I am developing an indoor positioning system using Bluetooth Channel Sounding (CS) on nRF Connect SDK v3.1.1 . My setup involves one Initiator and four Reflectors .
Implementation...
Hi Dev,
Development platform: NRF54L15 + NCS 3.2.3
We are facing an issue with ADC sampling. The code occasionally gets stuck/hangs inside the adc_read function. This...
Hello,
I am currently testing the Release Assistance Indication (RAI) feature on the nRF9151 (SMA-DK) in order to minimize power consumption after data transmission.
I...
Hello, I'm following BLE fundamentals course from Nordic Academy. İn Lesson 4 Exercise 3, with using Nordic UART service. We sent and receive data. However i'm having problem...
We are developing the nRF5340 for the Thingy91X based on Connectivity Bridge (NCS 3.2.4). I want to output logs from SWD and view them with RTT Viewer, but even when I call...
