Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hi
After updating to latest nRF Connect for VS Code i have an issue debugging my project with Ozone using the "Debug with Ozone"
With previous version the generated jdebug...
We are having difficult getting a R&S CWM500 to connect to our nRF9160-based device (operating in CAT-M1 mode). We are using a R&S test UICC. We have already attempted all...
We tested our project a while ago with nrf sdk v1.9.1 using the lte_ble_gateway sample (app on nrf9160, hci_lpuart on nrf52840 using a nrf9160dk board). Now we have developed...
The documentation says ...
The sample displays the following output in the console from the non-secure firmware:
SPP: send message: Success
SPP: process signals...
Hi,
I'm developing on the current setup:
nRF52833 DK, emulating an nRF52820.
Soft Device 113 version 7.2.0
SDK 17.1.0
IAR EW ARM 9.30
I'm trying to include...
Hello Team Nordic,
I am running a GNSS sample under SDK 1.9.0 and using modem firmware version 1.3.2.
I can get location without using A-GPS support but we get error...
The second instance of UARTE, UARTE1, was enabled in the configuration file. The receiving interrupt of UARTE1 failed to enter. Please help to check the reason
Hi everyone.
I am using nRF Connect SDK v1.6.1 (it's an old project) on a custom board with a nRF5340 on it.
The firmware is based on the central_bas sample project with...
Hi,
I am trying to create an ad-hoc network with several nrf5340 boards using 802154 radio, e.g. whenever each node transmits, others can receive the transmitted packets...
Hi,
I'm in the process of developing a new Matter device, using the Matter template as starting point.
When trying to commission the device it fails at step 8 (AttestationVerification...
Hello,
I am developing my own application using nRF Connect SDK with the nRF5340.
I want to drive multiple GPIO pins at the same time using the function gpio_port_set_masked...
Hi!
I am working on creating a Low Power mesh network and am trying to decide which communication protocol I should use with the NRF52840. There are no nodes in the network...
Hello,
I'm using NCS 2.0.1 on a nRF5340 board.
Currently I have some troubles with getting a response if I try to write a BLE characteristic from an iOS app. The write...
Hello, I am trying to disable using uart for console use Kconfig.
I am using sdk v2.0.2 (VSCode + nrf connect extension)
It works and the software works as expected. After...
