Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hi Team!
Does release 2.1 of the SDK address the issue raised in the below ticket with LWM2M implementation?
I have made the necessary changes to Asset Tracker v2 application...
I am looking at adding BLE to an existing design. The product uses an ARM micro, and currently has SPI and I2C available at daughterboard connectors. I am trying to understand...
Hello, guys.
I am using nRF Connect SDK, version 1.4.2 and nRF52840DK. I wonder what would be the way to print floating numbers during debug phase?
According to this thread...
Using the latest nRF_Connect_SDK
How can we set a udp/dtls socket, peer connect timeout for this call:
If there is no way to set a timeout for the call itself, is there...
Windows 10
NCS 2.0.0
We have run the Gazell samples successfully on the nRF52833 DKs. In these examples the CONFIG_GZLL_TX_STATISTICS is enabled (gzll_ack_payload_device...
Note: This might actually be a documentation issue more than a real problem because the build seems to work. But some clarification would still be appreciated.
We're developing...
I'm developing FOTA through LTE Modem which is made from QUECTEL(EC21KL)
On my custom board, nRF52832 is connected with EC21 LTE Modem via UART bus(TX : P0.16, RX : P0...
I am updating Nordic Thingy:91. I am following instructions on Nordic's DevZone web page: "Getting NB-IoT Demo running on Thingy:91
I have successfully updated modem using...
Hy
i am using a nrf5349 Dk board ,i am able to build and flash the board.
but when i am using this by building and flashing the board with hci_uart .in the linux system...
Hy ,
After i a buildng and flashing the hci_rpmsg as a cupapp . i flash the board
Then when i am checking the board with ubuntu laptop .i am not able to see the board...
Hi all!
I'm currently working on the UART on the nRF5340 board. The SDK describes three options: -polling API,
-interrupt-driven API,
-asynchronous API. With Polling and Asynchronous...
During development I noticed the following behavior:
If NRF_SDH_BLE_GAP_DATA_LENGTH=251 and NRF_SDH_BLE_GATT_MAX_MTU_SIZE=185, on Android devices the connection procedure...
Hi
For some reasons my Windows 10 laptop reports two JLink CDC UART Ports when I connect one of my nRF52SDK boards.My plan is to use this board with nrf Sniffer / Wirshark...
