I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
I have developed a Zigbee application using the nrf52840 DK board + nRF Connect + Zephyr and it is working. Now I am trying to move that app over to the nrf52840 dongle. It...
Hi, I am using nRF52832 development board and I have a motor driver. Motor driver has external power supply, I am just using nRF52832 to set directions which consumes low...
Hello, I am trying to use the dfu library to update the nrf52840 with a firmware stored in a littlefs file in an external qspi flash. I can successfully read the entire firmware...
Dear Nordic team,
it is very important for the RF and the HW engineers to be able to know the current transmit power of the modem. That will help us evaluate the network...
Hi
I'm looking for an example implementaion code on the nRF52840 without an operating system. Is there some example or application note?
I connected the SPI and all IO...
Hi,
I updated to VS Code V1.65 today and had some strange behavior with the NRF connect extension for VS Code.
After updating, clicking any "Action" in the sidebar (e...
I have already implemented DFU update in our one product. Which have fast USB interface and fast "lag-less" UART interface to nRF chip which is used as our bluetooth central...
I am using a code based on nrf52-ble-app-uart-c-multilink ( https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink )
If the central is working and the peripherals...
Board: NRF52833 (PCA10100)
SDK version: 17.0.2
Softdevice: S122
I am trying to perform USB DFU for my application. As I am using nrf52833 board, there is no available...
Hi ,
SDK 17.1.0
SD132
SoC - nrf52832
I am following the below given link to create custom service.
https://github.com/bjornspockeli/custom_ble_service_example...
We plan to use it with the Converter mode enabled for low current consumption.
However, if PIN is always set to Hi in order to use the Converter mode, about 300μA will...
After a lot of thought about the issues with TCP under EDRX or PSM , I have a feature request.
I would like if the application layer could know when a TCP socket was sitting...
Hi Nordic team
I tried ncs 1.9.0 peripheral_uart sample (\TOOLCHAIN\v1.9.0\nrf\samples\bluetooth\peripheral_uart) at PCA10095 v1.0.0 DK.
1. Application core: Board is...
