I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
1. ncs-3.2.4
I have a nRF54L15 IoT device advertising fine with ncs-3.2.4 (CONFIG_NEWLIB_LIBC=y), my FairPhone e/OS and my Samsung Android (using nrfConnect App or Serial...
Hello all !
Summary
While in power save the nRF7002 RPU powers down its receiver without sending a PM=1 (Null) frame first, so from the AP point of view the station...
Hi,
Our project has chosen nPM1300 as the PMIC, and our project's battery is only 28 mAh. When we tested the battery configuration file using the nPM PowerUP app, we found...
Hi,
I am testing on the nRF5340dk using NCS v3.4.0. I took the official Zephyr Extended Advertising advertiser sample (samples/bluetooth/extended_adv/advertiser) and added...
I have an application that will be greatly simplified if I can power the nRF52832 via the clamp diodes on the GPIOs. I have multiple GPIOs pulled up to around 3.3V with some...
I am developing a custom nRF54L15 board using a GigaDevice GD5F1GQ5REYIGR SPI NAND connected through the nRF54L15 sQSPI/MSPI interface.
I have encountered a highly reproducible...
Target device: nRF9151
NCS 3.4.0
Memfault Integrated
FOTA architecture in place with four slots, 2 in internal flash and 2 in external flash
Background COAP updates...
Hello:
Hello Nordic Support,
We are developing a battery-powered product based on the nPM2100 and nRF54L15 , powered by either a CR2032 or CR2450 primary coin-cell battery...
Hello, We're in EMC testing for a host product built on the nRF9151 (LACA A1A, FCC ID 2ANPO00NRF9151), running modem firmware mfw_nrf9151-ntn 1.0.1.
For our lab build, we...
I have dev kit nRf54LM20 - DK with specs: PCA10184 0.7.0 2026.12 1051821506 I am using 3.3.0 SDK. When I run peripheral sample project from NCS 3.3.0 it works completely fine...
Hello,
During design and schematic entry I used the online datasheet to select GPIO capability. I was advised that I should try out the pin planner to confirm that pin choices...
Hello, I have stumbled upon a case exposing a bug in your lib/date_time/date_time_core.c.
In my case the modem re-registered and got a time from the network (%XTIME) right...
Hello,
I have a question regarding SWD protocol v2 / TARGETSEL support on the nRF54L15.
My hardware contains two different microcontrollers:
• Nordic nRF54L15...
Hi,
We are using the nRF5340 and a Pixel phone for the nRF OTA update. We observed that the Pixel phone application disconnects after updating the connection parameters...
