Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I am current evaluating the SPIS for the nRF52840 and experiencing incomplete transfers from a connected master (Arduino). I'm sending 'hello world' from the master to the...
I have checked out and built the iBeacon sample in zephyr (samples/bluetooth/ibeacon) for nrfconnect version 1.7.1. I tried building for both the nrf52840dongle and nrf52dk_nrf52832...
Hi,
I have a custom 9160/mfw1.3.1 board with a set of matching networks and I need to setup MAGPIO to control these. This will only be used for cellular, not for GPS.
...
Hello,
We have produced a product that uses the 82520 chip. This product uses the NUS service. We want the Windows PC to use its built-in Bluetooth to connect...
Hello,
I need a PMIC for a lithium polymer rechargeable battery solution.
The nPM1100 from Nordic is interesting, but I see there is a cap on the output current available...
I cannot get the blinky example to work with my NRF52 development kit. I used the example in the pca10040/blank/ses folder and it worked fine. I then modified the code per...
Hi,
I'm evaluating a NRF52833 DK running the peripheral-uart example.
My Galaxy 10E can pair with the DK and the nRF connect Android app on the phone can find it and connect...
Trying to diagnose an issue, and looking for documentation on the memory mappings for the nrf52833 using S140 v7.2.0 - something like infocenter.nordicsemi.com/index.jsp ...
Hi,
We have a custom PCB with external crystal for HFCLK. Can you tell whether the external crystal is used by default for HFCLK or it has to be selected in the HFCLKSTAT...
I am using timer 3 as a counter for my capacitor discharge time. Currently, the value of is always problematic because it shows with too many deviation values sometimes...
Hello,
Is there any user manual to the nRF Connect for Android? I guess it is quite simple tool, but I am complete beginner in the BLE and would appreciate some description...
Hello All,
Currently we have a nRF52832 firmware .hex file for mass production.
And we use "nrf connect - programmer" to firmware programming without any problem.
...
Hi!
I'm updating to SDK v1.7.1 and I am looking at the changes in LwM2M Carrier Library v0.20.1. I was previously using LwM2M Carrier LIbrary v0.10.2
The big change is...
