Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
I'm trying to put my nRF52840 in System OFF and wake it up by DETECT signal on GPIO. For that I use gpio_pin_configure() with GPIO_INPUT | GPIO_INT_HIGH_1 flags but...
Hi i am involved in sdk5 based uart porting project
i can run example project and receive/send data to/from nrf52840-dk .
the problem is when i dig deep into the project...
Hi,
I am using a nRF52840 and SDK 15.2, and Soft Device S140 (BLE), where the device is battery powered.
In certain modes, the device sleeps to System Off mode, and...
I am currently porting the nrf_cc3xx_platform library to use it with RIOT OS . Following what has been done for Zephyr and FreeRTOS, I implemented:
Abort API
nrf_cc3xx_platform_abort_init...
Hello, I am working with the asset tracker v2 application and I want to connect it with Aws Cloud. I follow the steps corresponding to the tutorial and I am not successful...
I am trying to use the pc-ble-driver and as a first step want to use the heart_rate_collector example. I downloaded the source as follows:
I then followed the instructions...
Hi everyone,
I have an nRF52832 embedded as part of a dual chip (connected via SPI) and I'm looking to reduce the sleep current as much as possible. I'm currently measuring...
Hi, On both nrf52840 DK and Dongle, the sticker shows 4 info: - PCA board ID - version - year.month - Serial Number/MAC Address Could you please clarify what the last value...
Dear Nordic Community I am trying to get the nrfx adc driver to work with zephyr ( link ). With the help of this post , I ended up with the following code:
prj.conf -> ...
Dear Member,
I want to add ADC the main code,
but I got :
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol nrf_drv_ppi_init (referred from adc.o).
I'm using...
Hi, I am not sure whether there is I2C pins on nRF52840 Dongle board as based on the Adafruit Feather nRF52840 Express the pin is P0.11 and P0.12 as shown below: SCL 0.11...
Hello I am learning how to connect timers with gpio via PPI, i working on nrf52832dk.
So far I have connected the RTC 0 alarm channel to the LED no.3 (pin no.19) and its...
Hi, I am Shuang. I am now working on the Bluetooth direction finding function, but I have some problems, and I hope I can get your help.
I have experimented with Bluetooth...
I know Thingy:52-FW project has been marked as deprecated. https://github.com/NordicSemiconductor/Nordic-Thingy52-FW
However, I'm trying to get the development environment...
