Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
hello all,
I am trying to find the best power efficiency to transferring a pack of data(30 byte each time) from one nrf52 to another nrf52. I have a 80 uA in average power...
Hi all
So i had a working running example on SDK Thread and Zigbee V3.0.0. This flavor used the softdevice s140_nrf52_6.1.1_softdevice.hex I've migrated to the new SDK...
Hey All
I've found thread, dealing with this problem here: https://devzone.nordicsemi.com/f/nordic-q-a/77775/nrf_ble_lesc-nrf_crypto_ecc_key_pair_generate-returned-error...
I try to connect my nrf5340 CoAP server via my border router with CoAP Messages (with the IP address) from a computer. Is that possible? And if so, How?
I made a border...
I want to read peripheral's characteristics value in a fixed time interval or an event-based in the central.
I am using the nRF52840 Evalution board and SDK_17.0.2.
Here...
hi Support team,
Customer tested mesh SDK4.2, and now had one question:
their product is end node, and once button pressed, MCU is waked up and send the message to server...
in the gps example, there is a struct
nrf_modem_gnss_pvt_data_frame
in which contains the accuracy in meters, by documentation definition, it's /** Accuracy (2D 1...
Hi,
Facing some issue in creating sample application in vscode
nCS sdk V1.7.0, created sample hello world project and added build configuration for bl653_dvk
getting...
Hello all. Now I am making a BLE network with multiple peripherals and central based on NUS. How could I make data transfer between the central and specific peripherals? I...
Hello,
I would like to develop OpenThread applications that run under ZephyrRTOS for the nRF52840 processor. It appears that there are 3 possible development approaches...
Hello I'm trying to implement the DFU Trigger library into my project. to get following function:
" When the trigger library is added to an application, it allows a connected...
Greetings,
I am trying to get the nRF5340 DK to run on the coin cell battery attached to it. I removed the plastic and the USB cable then I put the "nRF power source" switch...
Hi team,
When we set fast advertisement timeout (uint32_t ble_adv_fast_timeout; /**< Time-out (in units of 10ms) for fast advertising. */) to a value greater than 0xFFFF...
i am using Laird smartBASIC for my programming of the BL653. I cloned the firmware of the evaluation board using the supplied Laird batch files and the J-LinkARM interface...
Hello, I have a question that I can't find an answer to in the documentation. The answer may be somewhere and I am just unable to find it.
My application utilizes sd_ble_gattc_write...
