Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi, I use NRF52833 and SW: NCS version 1.4.1 and its zephyr version is 2.4.0.
I would like to know if there is method to record program counter, stack pointer information...
Hi,
I have used "es_battery_voltage_saadc" in SDK 14.2 to read the voltage of battery, now I'm using SDK 17.02, but there is no es_battery_voltage_saadc.
Is there a better...
Hi
For the revision 3 of the nRF52832, I've updated to the nRF5 SDK V17.1.0 to apply the workaround for erratum 249.
Afterwards, I saw that there is a newer version of...
I have a BLE peripheral device using i2c, gpio. When the peripheral is not connected I want the lowest power consumption possible.
when i try to turn off gpio:
//sleep...
Hi Nordic.
I am using:
1. Mesh sdk V5.00
2. BLE sdk V17
3. NRF52840
I am trying to build a node with many elements and models. The software is based on the LC server...
A question regarding to nRFSDK 1.7: why does nRFSDK disable using BL2 inside TF-M? If our device needs BL2 with TF-M, how can we enable it? I can't enable CONFIG_TFM_BL2 if...
Hi Everyone,
I was wondering if it is something I do wrong, or if there is an issue with my module.
I have never managed to successfully upgrade the firmware of my nRF9160...
Hi,
is it any possibilities to multilink central with s112 in nrf52810 chip?
using sdk: sdk14
actually, i am using sdk14 with one central and one peripheral is fine...
Hello, All,
When using UART on nRF Connect SDK to communicate between nrf9160DK and nRF2833DK, I found that the data length of a packet sent by the UART on both sides is...
Hi,
I have started a new project that will use I2C and SPI devices. As a starter I took the example at /examples/peripheral/gfx/pca10040 since I am using a ST7735 based...
Hello sir,
I am using nrf52832 as Dev kit board with using Button 1 for long press event for an interval of 5 sec .I have defined the BT0_LONG_PUSH as BSP_EVENT_KEY_0 which...
Hi,
I'm trying to build the Zephyr NVS sample in SDK 1.6.0 and SDK 1.7.0 for nrf9160dk_nrf9160ns (Non-Secure) and build operation is failing with errors.
../src/main...
NCS V1.7.0
VSC IDE
In VSC you can create a custom board.
when i do this for the nRF5340 and build, it does not include the network core.
it also does not appear...
Hello
in order to reach low power mode I use the following :
bsd_shutdown(); // 3.4 ma.
nrf_regulators_system_off(NRF_REGULATORS_NS);
how can I recover from...
Hey,
I have a custom board that is pretty much the same as an evaluation board I got. I use the secure_bootloader_uart_mbr_pca10056 to enter and execute a DFU.
On the...
