Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
nRF52840
SDK 15.3
Segger Embedded Studio
I PWM a piezo buzzer (with a transistor) , using the PWM peripheral. The problem I encounter is that before I call the PWM...
hi support team,
i have a wired problem that i can't explain to customer:
first, i test this project "nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hids_keyboard...
I was able to successfully use the example ble peripheral blinky firmware example with the blinky mobile app. I added peer manager for passkey pairing but the blinky app is...
Hi Nordic Team,
I am using ble_advertising_advdata_update() to update some of the advertising data. I am doing every time the device is asked to advertise. In my code I...
the following report map is working when i try to increase volume on windows system (send 1 byte == 0xe9)
0x05, 0x0c, // USAGE_PAGE (Consumer Devices) 0x09, 0x01, // USAGE...
Hello,
my question concerns the layout of a bluetooth antenna & tuning circuitry for an nRF52832. Specifically, about two separate concerns:
1) Due to the shape of the...
Hi,
I want the received the datapacket from bluetooth to be stored in eeprom and access it when need be .If you have any small exmple codes for the same kindly inform me...
Hi,
We are migrating code from NRF Connect sdk 1.3.1 on nRF52840 to NRF Connect 1.6.1 on Nrf5340. Using SoftDevice as BLE controller on both.
Our existing code uses a...
Hi,
I want to run my application on the latest open thread libraries.
As per the page "infocenter.nordicsemi.com/.../thread_ot_libraries_building.html"
we need to run...
Hi,
We are using the nRF52840 Dev Kit with SDK17 and SD140 without FreeRTOS. There has been discussion in other postings <link> about increased current consumption caused...
Hi,
I am having a NRF9160DK board , which i want to use it for an simplest BLE application which sends the data from NRF52840 to my mobile using a simple BLE application...
Dear sir/madame
In our project we want to implement MAX17260 battery fuel gauge to monitor the battery status in the handheld device.
The interface towards MAX17260 is...
I'm trying to run the HID composite example on a nRF52840 dongle, and its not working:
- I refer to : nRF5_SDK_17.0.2_d674dde\examples\peripheral\usbd_hid_composite\pca10056...
Looks like 2 mistake in the latest nRF9160 production specification:
1: 1Mbps but 1200 in description section.
2: Power consumption could be in uA instead of mA.
Hello,
Sorry for the basic question, but I am trying to customize an application basing on the ble_app_cgms example.
In the debugger terminal on SES I am receiving the...
