Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Dear Sir/Madam,
we are trying to send large chunks of data (up to 512 bytes) via bluetooth with notifications with the added difficulty of an arbitrary MTU size. Our approach...
I am trying to update on nRF52 DK board with another, separate nRF52 DK board using OTA firmware updates. Essentially, I am trying to replicate how the nRF Connect Desktop...
hi...
i am using nrf52840 , segger.... mesh sdk 3.1 version in this case i want to send the simple message from client to server .how to do this ?
suggest me an idea ...
Hi,
I have some of peripherals at 1.8V and some at 3.3V that I'd like to run off the nRF5340. Is there a way to selectively set which interface is in a specific voltage...
Description:
We'd like to extend our existing bootloader. It currently supports UART transport and we want to retrofit a bootloader that also supports OTA via BLE. On merging...
I am testing the nRF9160 DK. I would like to know which SIMs are available in Japan.
I have confirmed that Sakura's Secure Mobile Connect SORACOM(Plan-KM1) works.
I'm...
I'm sorry if this has been answered somewhere else, but I couldn't find a thread that specifically addressed this.
Looking through the Modem FOTA options there is the...
Hi,
I'm working on a design with nRF52840 on PCIe Mini Size card. Since there is no VBUS rail on PCIe connector and I need a communication via USB, is it possible to bypass...
I see that I can USE BT MESH in an application . Can I encrease the number of advertisingh channel adding some secondary advertising channel?
May I do that in this way ...
Hello,
I come to you because I did not find the information on the web about sending MQTT data. I send a buffer of size 1408 with MQTT but I see in the configuration that...
Here is a screenshot of my current debug session. I cannot figure out why this if statement is failing. I have circled the relevant information. Even the disassembly indicates...
Hello,
I am trying to debug and develop in the net core of the nRF5340 and am having trouble flashing and debugging from SES.
I started by following the guide posted here...
Hello,
My board is connected to Gyro, Magneto sensor.
And board is sleep and wake-up by GPIO.
It usually works well. But time to time after wake-up from sleep mode...
Good Morning!
I try to update the modem firmware of a nRF9160 chip.
When I connect it with the nRF Connect v3.6.1 - Programmer (v1.4.10) and try to update the modem with...
Hi all
For the nRF52832, the total maximum sink and source current is recommended to be 15mA in this devzone entry .
Unfortunately, it seems like there is still no value...
