Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello All,
I am looking to use the nRF52840 for a ZigBee project. I am looking at the ZigBee light bulb example and following a few posts here I got it building. I can...
Hello,
I get the following errors when trying to DFU using a nRF52832 DK and the nRF Connect desktop application.
19:00:36.143
Attribute value changed, handle: 0x0F...
I want to build on the agps sample for 9160-dk
This involves changing the destination and format of outputs to cloud
I saw that multiple GPS hits are consolidated and...
Hi, Dear Nordic & all:
when I prepare to do a DFU example，I get trouble in installing "nrfutil" tool
I sure that I installed it successfully， but when I input "nrfutil...
Hi
I have a nrf52840 dongle with which already been flashed with ot-NCP binary and I want to over write this binary with new binary image[ot-rcp] in nrf connect for desktop...
hello,
I'm working with nRF52840 dongle, i installed nRF Connect for desktop v3.6.1 on ubunto 18.4 and i am using python3. After programming connectivity_4.1.4_usb_with_s132_5...
Hello I'm using Zephyr and trying to update the characteristic value with interval of 50ms. The problem is that the android app nrf connect freezes after I start reading the...
Hi,
I'm trying to run the light_switch sample app from nRF SDK for Mesh.
I have both PCA10056 and PCA10059, and I used both to run some other applications before testing...
Hi. I'm evaluating the nRF52810 chip by developing on the nRF52-DK (based in nRF52832 chip). As noted in this chapter https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17...
We need to work with the PWM, the idea is to set one frequency, duty 50%, and put out these pulses to one pin, we understand how to do that but we need to stop these pulses...
Hi,
I once got the following message while trying to attach a debugger to my network core.
After this event, I haven't been able to program my network core.
I have...
I am looking at the hardware design of Thingy91, where the antenna is shared by LTE and GPS/GNSS. My system will be connected to a cloud (probably most of the time) and track...
Hi,
Our NRF52840 (running 14.2) often takes a very long time to disconnect, from when a disconnection is initiated by the phone. It can take 30s, sometimes even more, for...
