Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Dear,
I am using NRF52840 and nRF5_SDK_17.0.0_9d13099 and SES development tool.
And also, I am testing SPI master with p0.29/30,31 and P0.26.
but when I do "nrf_drv_spi_init...
I am tring to DFU by Bluetooth with example, but it not work.
Please someone help me!!
My environment
PCA10056 nRF52840
SDK17.0.0
examples/dfu/secure_bootloader...
I was working with the Thingy:91 trying to get into into a serial printing state. I tried to updated the modem and firmware using the nrf Programmer. When updating the modem...
I've been having problems trying to get any of your example project to use NLOG to a uart port that we have made available for production test on our new product.
I've chosen...
Hi,
I am desperately trying to read some RTT Input with Zephyr, but I just cant get it to work!
All I want is to read the RTT Input. I tried with the console and the shell...
Hello,
I am looking at the nrf52840-dongle to explore Bluetooth audio (in headset mode).
So - just to double check:
(1)
I assume I can interface to bluetooth audio...
I'm using nRF52832 + SDK17.0.0 + s132_7.0.1. I am testing buttonless DFU on the PCA10040 board based on this blog, The initial DFU (when there is no app) is successful:
...
Hi, 1) I want to run the client-mesh from DK sources into Dongle. So, I did: - modified the client-dk project: nrf5_SDK_for_Mesh_v4.0.0_src\examples\light_switch_dongle\client...
Hi,
We have been working with a coordinator and a router device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
Hi Support-Team,
My iOS app crashed when I updated IOS-DFU-Library from V4.6.0 to V4.8.0.
I attached the Xcode debug info and iPhone Analytics.
Thank you very much!
Hello,
Would appreciate some understanding of a compiler warning. Developing for nRF52832 using SDK 15.3.0 plus S112.
This code compiles without warning:
Then I switch...
I have tried a lot of different settings but the NRF52810 still does not output carrier..
How do I configure the radio to only send carrier for NRF52810?
Hi,
I need to stream data from NUS UART Central Device to one peripheral, but the device always disconnects while trying to send second set of data. So I changed the write_req...
