Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I have seen other post on this issue but they are not helping. I am using the bmd 330 to run ble_app_uart. It compiles and advertises correctly but does not send the tx and...
Hi,
I am facing issues in Flash Data Storage (FDS).
Here, nrf_fstorage_write function is returns with NRF_SUCCESS but not writing in actual memory location. While nrf_fstorage_is_busy...
Hi. I am now at the stage of creating a new project. I want to include DFU over the air support in it. So, how can I do this using the example of two projects (secure_bootloader_ble_s132_pca10040...
How do you use the nrfx_temp driver in a project? I'm on SDK 17.0.2, segger, and an NRF52840-DK board. I see the old HAL temp sensor is deprecated and it seems to always return...
Hi,
I have been using a certain 16MHz oscillator up until now without any issues, and now wish to replace it for logistical reasons, what kind of testing are recommended...
I'm designing a product which incorporates a magnetic sensor (MMC5633) and a Bluetooth microcontroller (NRF52832). The sensor and bluetooth chip share the same ground plane...
hi,
We have some products that have been sold out(hardware:52832,software:sdk13,softdevice:s132_4.0.3).I want to upgrade their sdk to 15.3 through DFU.I learned in the official...
Hello,
I'm trying to modify the current ASSET_TRACKER of SDK v1.4.1 to get it to work in my own server on AWS-IoT.
I'm wondering if there is any documentation about this...
use SDK17.
central uses nRF52832 and peripheral uses nRF52810.
I want to implement the exchange of data with each other.
First, the central scanned and connected.
...
While using NRF52840 SDK with twi_scanner i am able to see i2c address 0x68, but while using zephyr unable to get the data.
I have seen I can configure i2c pins in board...
As I'm new to the BLE, I'm trying to make use of examples enclosed in the nRF5 SDK.
Now, I found that there exist several functions that seem like do similar things and...
1.4.8 programmer is complaining 'Error while getting readback protection' when connecting to the BL651, 453-00005.
Used to work.
Seems to connect OK to BL652-SA-01.
Hi,
We have a product using NRF52840 ready for production. In factory production environment we want to validate the product for PCB, product assembly etc failures and also...
Hi,
I am going to implement a PPI to connect GPIOTE event in with TIMER COUNT TASK, and then read the count from CC[0]. But the count in CC[0] never updated.
Basically...
Can I get suggestions on how to implement the following topology with respect to provisioning:
There are a series of lights and each of them is connected to a central...
