why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
In the Buttons and LEDs page, the LEDs are connected to P0.28-31 but in the connector interface page, the Figure 1 show LEDs connected to P0.13-16.
Buttons pins also looks...
Hello,
I am trying to create an application on my nRF52-DK using several custom service peripherals, each with 2+ characteristics. I have completed a few tutorials on...
Hi,
I am using USB device CDC, and the COM Port name on the PC is "nRF52 USB CDC BLE Demo (COMX), see the picture below.
How I can change it ? can I change it from...
Hi,
I followed the instructions described on https://github.com/NordicSemiconductor/pc-nrfconnect-launcher but I cannot "Start scan" within nRF Connect. It's greyed out...
Hi,
We just received prototypes of a new board with the nRF52840 and now we have a reset problem.
When the board is reconnected after a long time (no voltage remains on...
Hello,
I am testing the multilink BLE (1 central : n peripheral) UART example.
I am using Github code and tested it.
The central example is(SDK 16.0.0):
https://github...
Hi, I've just compiled clean examples from Zigbee and Thread SDK 4.1.0 and I'm following instructions from here: I've got CLI on the nRF dongle and multi_sensor example loaded...
Hi Nordic experts:
I am working with sdk 17.0.2 nrf52840 ble_app_uart example project. I added twis i2c slave functionality in this project, and the project is working fine...
Hello everyone.
I want to assess the range of my current setup, theoretically. And I found this useful online "calculator": www.bluetooth.com/.../ (please scroll down until...
Hello,
I wanted to implement WDT resets when my application hangs. I am working on the advertiser code, what I observe was when I implement WDT driver in SDK 15.2 examples...
Hi,
I have been working with mesh and I'm using the version 4.2 Mesh SDK.As I understand it I should use nrf_mesh_serial_tx() api to send serial message.When I use this...
Hi There,
I'm working on a datalogger project using nrf52840, includes BLE also. I'm using external 24 channel ADC and should be able to log data to the SDCard at the rate...
Hi, can you explain shortly is it possible to use OTA functionality from FreeRTOS application? I wasn't able to found such an example, and I'm wondering about the possibility...
Most times the Online Power Profiler doesn't even load the graphics, etc. 80% of the time it doesn't finish loading and I have to reload multiple times. I have a 1 Gigabit...
Hello,
I'm using nRF52833 for my application. Unfortunately, my dev kit can not connect to my PC when I use cable to connect it to my PC. It can supply voltage for my kit...
