When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi,
I see there is a differenece between v1.0.0 and v1.1.0 in the asset tracrker's main loop.
i.e. poll function vs the sleep function.
does this result in a change...
Hi,
I'm working on a custom bootloader which does DFU over I2C. As a fail safe mechanism I want to have a timer running that gets reset between each Image data block, so...
When using SDK v13's I2S driver, the data to send is filled via data_handler callback. How do I fill last block data?
Assume i2s buffer size is 2000, then every 1000 words...
I have been going through the steps in this blog post: https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/getting-started-with-nrf9160...
Hello everybody,
I'll try to modify the ble uart example. The target is, to get data from two different nus Services (different characterisitv uuids). They are both initilised...
I basically need to use two UART instances with the BLE Buttonless DFU Template App.
I started using the Serial library but apparently it's no longer supported.
The methods...
Hello,
I am working on nRF52832 SDK 15.3.0 in segger studio.
In my project I have 2 ADC input pin.
ADC initialization is as shown below,
And every 0.5 second I read...
I have a custom BLE characteristic that I want to use to allow an app to send commands to my device. I use an on-write() function that is called whenever a BLE_GATTS_EVT_WRITE...
The Device's name UUID for Thingy52 in according to this site https://nordicsemiconductor.github.io/Nordic-Thingy52-FW/documentation/firmware_architecture.html is: EF68xxxx...
Hi I am using nrf52840 on a custom board with segger embedded studio as development IDE. I would like to flash the hex file generated without using segger embedded studio...
do you have a user gide for Serial DFU just like buttonless DFU ,like this link https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics...
Hi,
I have flashed lte_ble_gateway on nRf9160 DK (PCA10090) and hci_uart on nRF52840 SoC.
After flashing, I am getting some random RSSI values and MAC Address , instead...
Hello,
I have two micro-controllers communicating over SPI.
The STM32F746 is SPI master. The nRF52840 is SPI slave. I use SDK v15.3.
I am sending two bytes over SPI...
