I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
I get the following error when launching the app, and the "Start scan" button either doesn't do anything or can't be clicked.
Error while probing devices: Error occured...
Hi
I am measuring the current consumption (with an amperemeter) of the nRF52 on the PCA10056 Devboard. The nRF52840 is supplied directly by connecting the external power...
Hi,
I have a problem when I do a write request on a 20 bytes characteristic from a custom service.
The funtion sd_ble_gattc_write return error 0x7 but I can't find what...
I want to stream a mono audio signal with high bandwidth (20kHz) from a remote device to a base device.
Need to A2D signal on remote and D2A the signal on the base. Low...
Hi,
The SEGGER have released a JLink software version that support to use JLink on ARM Linux platform。
I try it on raspberry pi, and it work well. But when i use pynrfjprog...
Hello.
I have a project that use the NRF_LOG_INFO for printing messages, and it is work O.K.
Now I add a part that need also to get parameters from the terminal.
I can...
Hi
Please advise when I can find firmware for nRF52840-DK which can send advertising packets or any data packets at data rate 125Kbps and +8dBm output power
I have two...
Hallo Everyone
We have developed a firmware for our systems using the nRF52832 with BLE 4.0.
Now we need to move to BLE 5.0. As far as I know the nRF52832 works with...
I get a strange error message reading from my hdc 1080 temp/rh sensor:
[00:08:38.013,916] <err> i2c_nrfx_twim: Error 195952641 occurred for message 0
I csnnot find any...
Hello Everyone,
I am working with nRF52832 chip on our custom board. I am using SDK 14.2 and SD v5.0.0 for development on a windows platform with Segger ES.
I am looking...
Hello all, I'm using nRF52 DK.
I'm going to use this DK as a master of BLE, and send information which is from BLE peripheral device to another board using SPI.
Anyway...
I am trying to implement the MAX30105 pulse oximeter sensor along with the Nordic Thingy 52 application source.
I referred the sample ADXL375 code provided by Simon here...
Hi,
I got some issues with migrating from SDK 14.0.0 to SDK 15.3.0 on a project that was developped from the previous developper. I have already done a lot of migration...
