Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I am not able to program the nRF52840DK by copying over the .hex file generated by my project to the JLINK drive. However I am able to successfully program using Segger directly...
Hi,
We are looking at using the key:value store functionality defined in mesh_config.h. Can you provide some additional detail on
HW and or SW configuration required to...
Hi,
We are trying to develop a system of IMUs for motion tracking using multiple Thingy boards and an nRF52832 board. The Thingy boards are used as IMU sensor nodes and...
Hi, This is M.Irfan. I want to send data (collected by mpu6050 sensor) using Bluetooth in my cellphone and want to save it. Can you help me with some example code of sending...
We noticed issues regarding BLE activities when running our custom bootloader. It seems that we have located the cause but would like to have approval for that behavior. ...
Hi All
I am trying to find some example code which uses easy DMA over UART using nrf528240..
Using sdk version 15.0. The example which is available by default uses the...
Hi,
I recently bought a nRF51 Dongle (PCA10031) and a nRF52840-DK (PCA10056) and I am now trying to use it for BLE sniffing with Wireshark. I am running OS X 10.14.4.
...
I compiled 4.0.0 in the past and the generated libraries were named "pc_ble_driver_shared_sd_api_vX.dll".
Now I compiled 4.1.1 and the libraries are named "nrf-ble-driver...
Dear Nordic:
My nRF82832 codes based on nRF5_SDK_15.2.0_9412b96 and used s132_nrf52_6.1.0. But I find the Bluetooth signal of nRF82832 can’t be scanned by smart phone which...
Dears,
I am using DK PCA10028 (V1.2.2). Start developing from SDK_12.3.0\examples\ble_peripheral\experimental_ble_app_blinky.
All system configuration keep the same (ADC...
Hi,
I'm using:
nRF52840 Preview DK
Zigbee v2 (nRF5_SDK_for_Thread_and_Zigbee_2)
Segger Embedded Studio for ARM 3.52
Developing on a MacBook (macOS Mojave v10.14...
2017-04-12T06_05_42.374Z-log.txt
Hello,
the example "experimental ble app cgms" (SDK v13.0.0) failed to pair with nRF v1.1.1.
The error code was Authentication failed...
Hi, guys. I'm using two PCA10040 boards. One is using the ble_app_uart__saadc_timer_driven__scan_mode example
github.com/.../main.c
and the other board is flashed with...
