Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi
ZED requests beacon every time when it restarts both case ERASE_PERSISTENT_CONFIG is true or false.
But
ZR does not request beacon when ERASE_PERSISTENT_CONFIG is...
Hello,
I've been using the nRF52832 with a Segger JLink Pro which works fine during execution. However during the system initialisation, this is just before getting to the...
Hello,
I have used nRF24L01+ in one of my scientific paper. I need to provide a detailed reference as a citation in this paper. I couldn't find the documentation of nRF24L01...
Trying to have the Nordic Thingy advertise to the ESP32. Using example code found in the ESP32 BLE Arduino.
When running the program, BLE Client, we are able to see and...
hi all,
how to revert interface MCU ATSAM3U2CA-AU(J-link )
when i plug in usb port to PC, DK board can't active .(PC can't detecting any USB Emulators)
check list...
Hello, I am using nrfgo studio to flash softdevice, application and bootloader on nrf52832 I am getting below issue:
" This hex file has data in SoftDevice region. Try programming...
We are using v0.4.0 lte_ble_gateway example running on an nRF9160-DK (0.8.5)
We are successfully pushing data from the UART on the nRF52840 to the nRF9160
Also managed...
Hello, I'll buy ISP 4520 (based on nRF52832) kit.
I request information about the processor's 'power down' of the LORA / BLE combo module.
Depending on the wake-up method...
I am currently working on adding the ambient light sensor to the asset_tracker application firmware. I have managed to configure the I2C, configure the sensor and read the...
I am developing an application as a peripheral based on the NRF52 SoC which regularly reads a sensor and publishes the reading to a BLE characteristic. A central (a smartphone...
I'm building some of the samples using command line in Ubuntu and have a strange issue. Everything builds fine, the merged.hex file is generated, however when I try to flash...
Hello All,
Currently i am working on nrf51422 DK board(PCA10028). I am using SDK 12.3.0 ,from this i have referred the ble_app_uart example for implementing the UART and...
Hello,
After following the steps of the tutorial : https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/getting-started-with...
