Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
I use the LAIRD module BL652 with an nRF52832 with the SoftDevice 14.0.0 (old version…).
The application use the BLE with the SoftDevice.
We have mesured the...
Hello,
Here i are using nRF52832 ,softdevice S132 and mesh sdk v3.0.0
For my Application,i need to go with DFU.so i merged my application into the example code of DFU...
Hello,
Does anyone know if the FreeRTOS port that's distributed with the nRF5_SDK_14.2.0 is intended to support nRF52810 chips (which have no hardware FPU)? I started working...
SDK 14.2 keil5
I want to run freertos with nrf52810.but I did not find any example .
Is there anyone have tried this?
I downloaded nrf52832 code(ble_app_hrs_freertos...
Hello All,
I have looked around for answers to my specific issue, however I did not seem to find one that aided me enough to fix my issue.
I have created a BLE profile...
Hello,
SDK 15.2, SD 6.1.0 with PCA10056 1.0.0, 2018.20. nRF Connect App v4.22.3. Pixel XL.
I'm running into an issue with my application where the phone disconnects after...
Using: Linux (Ubuntu 18.04), gcc/Eclipse, nrf52840, v15.3.0 SDK, SD 6.1.1
It has been a real bear of time using the SDFU in the newest version of the SDK. There were a lot...
Dear support,
Our team is considered doing their own smart watch, so i found that nRF52 chip is a nice solution. Just before we start, i would like to do some basic questions...
When we ported our FreeRTOS based project to SDK 15.3 from 15.2, we noticed a big jump in the CPU Usage. It turned out that the issue was in SDK 15.3's freertos port_cmsis_systick...
Hi nordic,
I send multiple bytes but always only receive packets of length = 1. For example in the picture, I sent 2 bytes 0x68, 0x69 ('DE') but only received the first...
Hi
What is the difference between ble_nus.c and ble_nus_c.c?
because i went through both the files and i felt both files are almost same except an extra function(db_discovery...
Hello, I bought a nRF52832 Breakout Board from SparkFun. from their tutorial, you can program this board using the serial bootloader and the Arduino IDE. However, aside for...
I am trying to operate a BLE5 sniffer with nrf52840dk
After connecting the dk to nrf connect desktop and programming it with a wrong code (by mistake), it is not able to...
I'm using the nRF52840 DK.
I managed to burn the on-board nRF52840 MCU several times, using the nRF connect windows app.
After several such successful burns, with various...
