hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
hi......
my peripheral device is heating up quickly what is the way to reduce or avoid heating of the device ?
when i put my device in sleep mode more than the wake up...
Using SDK_14 and unmodified SAADC example on pca10040.
Initially connected A0 (PO.03) to ground but getting seemingly random values.
<info> app: ADC event number: 586...
The file components/libraries/timer/app_timer_freertos.c does not have the function app_timer_cnt_get() defined. Compiling libraries that require it (like external/lwip/src...
I used nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\peripheral\spis to test spi,but only the first time can receive data. logs like below,"1234567"
is I send...
static void onoff_state_value_update(app_onoff_server_t * p_server) { /* Requirement: If delay and transition time is zero, current state changes to the target state. */ if...
My app (using S130v2.0.1 nRF51822 SDK12.3) triggers app_error_fault_handler (seen on a PIN; since not able to debug due to timing) on sd_softdevice_disable(). A snippet of...
Hi,
I am using nRF5_SDK_12.3.0 and based on \ble_peripheral\ble_app_uart ( with softdevice of s130) to build my application.
Recently, I tried to add the wdt to my nrf51822...
I adapted the light switch demo of the nRF5 SDK for Mesh for sending a series of reliable on/off messages sequentially from an nRF52840 Preview DK to 20 Thingy:52 servers...
Hi. I have set up a nine node mesh using Thread and the nRF52840 chips. I am using the COAP example. All my nodes are visible and i am able to send pings between them. I am...
Hello I have the dk board and am hoping there is some example or tutorial to help me get started with my project. My goal is to use the nRF52840 as a master to multiple devices...
I have modified it so that it works with two nRF51 DKs, one acting as a central and other acting as a peripheral.
The base UUID for this service by default is
{0x9E...
Hello,
First, my setup:
nRF52840 Dongle
Softdevice S140 6.1
SDK 15.2
I built my own adapted application code based on the multilink central example and managed...
I am new to the Nordic chips and for my project I am using an NRF5832 module from Accono. My question is how to get the free SES license for Nordic? When i go to license.segger...
