why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hello,
I am trying to estimate Battery life. I am using CR2032 with 230 mAH capacity. I am confused with the calculations.
As per excels sheet in below link, for 500...
Hi, I have strange problem using pc-ble-driver on nrf52 with heart_rate_monitor example. When I set advertisement data to be 16 bytes long, two of our testing phones cannont...
Hi,
I am using nRF52832 and I need to create a timer interrupt handler, which can trigger at 417us (microsecond). I am using Segger Embedded studio. Please, can anyone help...
I have a project which recently started logging the following error on boot.
nrf_sdh_ble: sd_ble_enable() returned NRF_ERROR_NO_MEM.
This is the only log message....
Hello
I have a simple Thread network with 3 nodes and I would like to send a provisioning request from one to the 2 others in order to get their IP.
I modified the Thread...
I will like to know if the nRF52832 is capable of working properly when placed in series with a 30 Ohms Resistor ( which is the battery resistance for our application) at...
Hello,
As nordic has implemented sdk for mesh and i have been using mesh sdk v3.0.0 LIGHT_SWITCH_EXAMPLE but i am facing some problem regarding pa_lna. Actually wt i have...
Hi,
I want to use I2S to drive the speaker,just like playing the prestored samples from sounds.h in thingy:52.
However,i can't drive the DAC by I2S.Is there anyone have...
I just got my nRF9160 DK. Unfortunately the out of the box demo didn't work:
LTE LC config ... [00:00:01.029,876] [1;31m<err> net_if.net_if_init: There is no network interface...
Imagine following use case:
Alice has a peripheral bonded with Alice's phone (central)
On the peripheral, Alice switches to a "guest mode" which disconnects from Alice...
HI
UUID scan filters are set and enabled.
I was capturing peripheral device MAC id via ble_evt_handler.
i was expecting filtered devices should be visible but when i...
HI
I am trying filter peripheral devices based on UUID while scanning. I have set, enabled the scan filters but still output is displaying all the peripheral devices irrespective...
Hi I am using nrf52832 board and SDK15.2 I have below requirement:
Nordic board should act as central as soon as it gets booted and scan for particular service if present...
Hi, I have modified the twi_scanner example of the 52840 DK to be compatible with nRFDongle.
I fully erased the dongle with Segger and passed the new hex file with SWD cable...
I found this very useful Throughput Measurement Application for for Threads: http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee.v2.0.0...
