Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi, there is a code comment "Workaround for PAN_028 rev1.1 anomaly 22 - System" in nRF5_SDK_12.3.0_d7731ad\examples\proprietary_rf\esb_low_power_ptx\pca10028\blank. So, I...
I would like to do I2C BlockRead using nRF52.
devzone.nordicsemi.com/.../i2c-block-read When I looked at it, I found that it was not possible to receive variable length...
Project migrated to SDK 15.3.0 with Softdevice S340 6.1.1
Project is using DFU secure bootloader. The example in "dfu/secure_bootloader/pca10056_ble" was used as the starting...
Dear nordic,
I have some doubts regarding PWM. i want two PWM out both are working different frequency and also i need softdevice. I think PWM can make two ways one is using...
Hello,
I want to change the 16-bit of 128-bit UUID at runtime. is this possible?
let me explain...
1)the first both central and peripheral set 128-bit UUID like this...
Hi,
Actually i m new on this field.
I m making indoor navigation by using nrf52840 soc.And i m using sdk15.2.In that sdk i used beacon app code for advertising beacon...
Hi.
I use a modified lightswitch server application with Nordic SDK 15.2, Mesh SDK 3.1.0 and Softdevice 6.1.1.
During provisioning I experience a software assert with...
Hi,
I want the bit rate to be 125Kbit or 500kbit. The project uses 1Mbit and 2Mbit. I'm investigating the topic on the Devzone blog. I reviewed the example nrf52840-long...
My work need to use 4 gpio interrupt, but it not work when use freertos on nRF52832 ,sdk version 15.0.0. My code is like below:
err_code = nrf_drv_gpiote_init();
nrf_drv_gpiote_in_config_t...
I created own app button library. It's just return handler into main with number of pin and type of push - short or long. Also I created library for rgb_led (using nrf_pwm...
Hello everybody,
I'm using nRF5280 (Laird BL654) with SoftDeveice S140v6.1.0 and SDK 15.2.0 with a modified version of the blinky peripheral example.
I've changed NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hello
Our custom board has two chip configurations for BLE stack. The two chips communicate with each other through UART. Both chips are running zephyr with two chip configuration...
I'm writing an app to that talks to the Thing52 over BLE, and using this as a reference: nordicsemiconductor.github.io/.../firmware_architecture.html For Battery Services...
Hi,
We just recently bought the nRF9160_DK board and compiled and loaded the AT_Client onto the DK. We have followed all the setup instructions for the SIM card for iBasis...
