Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I'm using NRF52840 sdk v15 with Softdevice.
I have multiple SPIM instances and I make sure they are never active at the same time.
Can I share the pins (except the...
Hi, I'm trying to rate nrf52832 with stack ble_app_uart softdevice. My IDE is the IAR workbench for ARM 7.80.4. I downloaded the latest version nRF 5_SDK_15.0.0_a53641a, which...
Hi:
I would really, really, love it if you could provide a Segger SDK for Thingy! I've seen a few threads in here about the work to do it and it's a struggle. I noticed...
Hi there,
I've been searching around this forum for a while and still haven't gotten any reliable answer. I'm trying to develop a OTA firmware upgrade solution for the ATMega328p...
Hi:
when I compile project Thingy_ndoe in solution Thingy_node_s132_pca20020, an error meet,
C:\Nordic\thingy_sdk_v2.1.0\mesh_sdk\mesh\access\src\nrf_mesh_node_config...
I have combined the light switch server and client model to build control model. When i start provisioning for control model opcode status field : 2 error occurs which means...
Hi ,
I search nrf52810_bitfields.h , but i don't find about start bit , is the direction search for error ?
My idea : This is set up for stop bit , should the start bit...
Hi All,
I have serious difficulties to work with this board. I'm a beginners and I did not find any tutorial where I could said...oooh great I understood. My goal is to...
Hello all, I am trying to write a program that that updates the firmware on an external chip from a smartphone over BLE. Currently my approach is working but quite slow and...
Hello,
I am using a nrf52840 DK and I have no issues connecting to nrf connect. However, when it's connected all LEDs turn off and whatever code that was inside stops functioning...
Hi
I am programming NRF-51 board using nrfgo studio, it was working fine previously but now it failed to detect the board showing error. I shared screenshot of nrfgo studio...
Hello everybody,
I have integrated the new S140-SD-v6 Stack 6.10 into the github.com/.../nrf52-ble-app-uart-long-range Example.
It built and compiled without any errors...
Hello,
I want to get the raw acceleration of the Thingy 52. however I can't understand the values I get from the raw acceleration. What is the unit used for raw acceleration...
I am using Nordic SDK 13.0.0 with PCA 10040 dev board.
I have configured the stack to use MAX_BLE_MTU_SIZE = 200
// Configure maximum size of ATT packet the SoftDevice...
Hi,
I encountered a weird behavior. i defined characteristics with specific read/write permission however all the characteristics are writable for some reason altough the...
