hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hello guys, I was doing some testing with the QSPI component, and noticed exceptionally high current draws depending on whether the Peripheral was on, off, and if the Macronix...
I’m designing a board with nrf52840. For the RF layout part I’ve followed the reference design apart 3 pads near the pcb antenna.
The question is: How much is indicatively...
working environment:
SDK:12.3
WIN8.1
hardware:nrf51822_qfaa
nrfjprog:9.8.1
problem:
using nrfjprog to program application(s130 + bootloader + application),application...
Hi,guys
I got a problem. I tried to create a service to control led over BLE, when i finished, it can advertise, everything was ok. But when i tried to write 0x01 to control...
BT832 connect to a passiv MEATER temperature senor. How should I configure the Device with AT-commands. I use Docklight to send AT-Commands from my BT832.
Hi Team,
I want to connect the nRF52832 based custom board to AWS-IoT cloud.
The Simcom 2G module is interfaced with nRF52832 over UART.
Can someone guide me from where...
hello everybody,
In my application i want to check if a password is set, to enter bootloader, otherwise don't start the bootloader.
This should work without bonding. ...
Hi, I'm new in the use and development of chip.W here do i start to develop myself?
eg my first aim is to make bluetooth headset compatible with android. Can you help me...
Hi, I have been looking at the following document nRF9160_OPS_v0.7.1-1510217.pdf which I had downloaded from the Nordic website today. In particular the layout guidelines...
Hi,
I run the "ble_app_uart" from sample program and leave it as it is. The program ends in NRF_BREAKPOINT_COND with "Fatal error" after a while. It is displayed as a screen...
Hello
I am using the nRF52832 with SDK 14.2, JLinkRTT Client, and SEGGER IDE. The system simultaneously runs a soft DAC, IMU, digital potentiometer, and provides variable...
Hi all!
I want to use the BLE stack by Nordic. I figured out that S132 is the appropriate HEX image for nRF52832. I can burn the softdevice into flash with nrjftool.
An...
We have an application where certain executions hold more priority over BLE link. We are implementing a critical section(disable/enable interrupts). However, in some corner...
