Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
I am wondering why the ccm library uses the software aes encryption. Is there anything wrong with the hardware encryption so that it should not be used?
Marius
Hi there,
hope you are doing fine.
I am using SDK 14.1 with SoftDevice 132 as well as a state machine framework which needs a have a function called periodically to...
Hi. I'm using nRF52832, SDK13.0.0 as peripheral.
When I want to disconnect central, I'm using sd_ble_gap_disconnect function as below.
err_code = sd_ble_gap_disconnect...
When I try to build and run any example from the nRF5 SDK, it can compile successfully. But when loading to the eval kit, it can't find the 's140_nrf52840_5.0.0-2_alpha_softdevice...
Hello Everyone,
I am using nrf51822 256Kb Flash and 32KB RAM Raytac's BLE module with SDK11, S130 with over the air Bootloader (16Kb).
So the aim is that when a particular...
Hi all,
I encountered a problem , when I connect 1 board central to 2 board peripheral via NUS . It connected and discovery success . But at
static void db_disc_handler...
I was compiling a project(ble_app_uart and I am using PCA10028), it was not successful and KEIL5 display this:
it looks like I didn't install NordicSemiconductor.nRF_DeviceFamilyPack...
Hello,
I use a nRF52832 device, and I have some strange behavior when I use PWM. You can see my test program listed below.
Thank for your reply, Thierry!
/*
* Test_PWM...
Hi. I am a newbie in Nordic chips, quite knowledgeable in Atmel AVR, though. I'm working with an nRF51822 on a board like this www.waveshare.com/.../BLE400 . I use the Mbed...
This might seem like a really banal question, but i could need some clarification on this.
My understanding is that the config_client should be used on the network provisioner...
I want to connect a ST Chip (LSM6DSL - Datasheet ) via SPI with the nRF52840 Preview DK (SDK13) - NRF_DRV_SPI_MODE_0
When I am using the SPI Master example with different...
Hey Guys,
Thanks for this wonderful first of all.
Great work!
Well I am posting my first query related to Nordic mesh, please help
we need the BLE for our Wireless...
I would like to use connection handle value as index to an array which store some per connection specific data. Some questions about connection handle:
is connection...
I am using example DFU project (bootloader_secure) from SDK (12.3).
Chip 51822QFAA.
My problem is that I cannot start to debug session in Keil5. Use JLink.
I can program...
