When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi,
I have a python scipt that uses pynrfjprog to program some custom information into a board's flash to be used by my application (calibration parameters, serial number...
I managed to compile the ble_app_uart on windows 8.1 with cygwin. I had to remove all abspath on the makefile, as launchpad gcc is not compatible with cygdrive notation.
...
Hi, I use the NUS most of the time.
(SDK 7.2 & S110 7.1 with IAR 7.1)
As you know, HID keyboard or mouse bond with centrals (smart phones).
After bonding, when using...
nRFgo was unable to read attach to the boards I have with the QFAABB parts, but reported QFAABA parts correctly and programmed them. nRFgo was at 1.21.02.
I updated to...
Hi,
I'd like to retain a value in RAM after any type of reset, including a watchdog timeout, so that I can read it back in the bootloader immediately after a reset.
...
Hello,
I followed the tutorial to use Eclipse GCC and both examples (blinky without softdevice and HRS with S110) work fine, i.e. I can build and flash them.
Now I try...
Hi,
First of all I appreciate the way nordic has put tutorials on the website for the newbies.
I am working with putting custom services in my code, and its working...
Hi everybody!!!
I am working on ANCS on NRF-DK51 (nrf51-sdk-9.0.0) and I get the disconnected reason 0x002A same as this topic . They said that to overcome this problem...
Hi,
I am using nRF52382 controller and we are planning to put RTOS on it. Is it possible to use the same RTC for system ticks as well as to set current time?
In the Example "ble_app_cts_c_s132_pca10040 " messages are send to the UART output, by default the UART Hardware Flow control is active. I would like to disable the Hardware...
We have designed a product using Nordic's nRF51822 and will be selling into Korea and Taiwan market.
Recently, there is a new requirement for us to provide antenna radiated...
Hi
I started form the lbs example to build my application. I have now the following problem:
apparently the button_event_handler is only triggered when the device is connected...
Hi,
I have searched the forum, but still I cannot find answer to my question. I designed my custom board for nRF51422 and want to work with ANT (softdevice 210) (I have...
